Restoration Hardware Bistro WOD52AGV5RW Installation Manual Download | Manualshive

Page: 1 / 11

background image

Installation Guide

Table of Contents:

Safety Tips. pg. 1
Unpacking Your Fan. pg. 2
Parts Inventory. pg. 2
Installation Preparation. pg. 3
Hanging Bracket Installation. pg. 3
Fan Assembly. pgs. 4 - 5
Wiring. pgs. 5 - 6
Canopy Assembly. pg. 6
Blade Assembly. pg. 7
Automated Learning Process./
Activating Code. pg. 8
Wall Control Operation. pg. 8
Remote Control Operation. pg. 9
Testing Your Fan. pg. 9
Troubleshooting. pg. 10
Parts Replacement. pg. 10
Warranty. pg. 10

net weight of fan: 17.2 lb (7.8 kg)

PRINTED IN CHINA

READ THESE INSTRUCTIONS

AND SAVE THEM FOR FUTURE USE

E192641

RESTORATION

HARDWARE

For Model:

Bistro Ceiling Fan

WOD52AGV5RW

1
2
3
...
»

Summary of Contents for Bistro WOD52AGV5RW












Reviews:

No comments

Related manuals for Bistro WOD52AGV5RW

Brand: Lasko Pages: 2

Brand: Sabiana Pages: 49

Brand: Oster Pages: 10

Brand: HTW Pages: 44

Brand: Savoy Pages: 27

Brand: Valueline Pages: 28

Brand: RP LIGHTING Pages: 16

Brand: Sioux Tools Pages: 15

Brand: Kemot Pages: 20

ROANOKE YG216-MWH

Brand: HAMPTON BAY Pages: 19

Brand: HPM Pages: 4

Brand: Parrot Uncle Pages: 4

Brand: ebm-papst Pages: 9

Brand: Vinco Pages: 25

Brand: Fancom Pages: 83

Brand: Coopers of Stortford Pages: 7

Brand: Sharper Image Pages: 29

GALAXY GBD Series

Brand: Vent-Axia Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands