background image

Note: 

● For best battery performance, charge for a minimum of 4 hours on 

first charge.

RF radiation information

This product is intended for professional applications that meet FCC RF 

radiation requirements. Users must be aware of the hazards of RF 

radiation and take appropriate measures to meet the requirements of 

RF radiation limit.

Common sense in RF radiation

RF refers to the electromagnetic frequency that can be radiated into 

space. It is a technology widely used in the fields of communication, 

medical treatment and food processing. It will produce some RF 

radiation during use. 

Security in RF radiation

 To ensure the physical and mental health of users, experts from 

science, engineering, medicine, health and industry, together with 

relevant organizations, have developed radio frequency radiation 

standards and guidelines, as shown below:

● United States Federal Communications Commission, Code of Federal 

Regulations; Vol 47, Part 2, Subsection J.

● American National Standards Institute (ANSI) / Institute of Electrical 

and Electronic Engineers (IEEE) C95. 11992 and 11999.

● Standard issued by the International committee on non-ionizing 

radiation protection (ICNIRP) in 1998.

Federal communications commission regulatory 

requirements

In accordance with the regulatory requirements of the federal 

communications commission, terminals must comply with the 

regulations of the federal communications commission on radio 

frequency radiation limits, or they cannot be sold in the United States 

market.The manufacturer is required to inform users of the matters 

needing attention by putting labels on the products, so as to improve 

users' awareness of radiation prevention.

Control and operating instructions of RF radiation

In order to maximize the performance of the product and to ensure 

compliance with the radiation limits in the relevant occupational or 

controlled environment of the above criteria, the sending time shall not 

Indicator display

Red light

Green light

Current charge status

In charging

The charging is completed

DIGITAL TWO WAY RADIO

DIGITAL TWO WAY RADIO

Security and overview

Preparation before use

Battery information

1exceed 50% of the rated factor and shall follow the instructions below:

• RF radiation is generated only during transmission (speech) rather 

than reception (listening) and standby.

• The distance between the terminal and the body during transmission 

should be at least 2.5 cm.

           Be sure to ensure that the product is off when charging. Battery 

into the charger may be charging red flashing constantly flashing, this is 

the battery power is too low, the charger to protect the battery 

pre-charge process, is a normal phenomenon, Generally continue for 30 

seconds to turn the red light of the normal state of charge.

Please use the charging seat specified by our company to charge the 

battery, the charging seat indicator shows the charging status.

1. Plug the power adapter into a power outlet;

2. Plug the other end of the power adapter into the socket on the back 

of the charging cradle;

3. Insert the battery or the battery-equipped product into the charging 

cradle correctly; the indicator light on the charging cradle shows the 

charging status. When the indicator light is red, it indicates the start of 

charging. When the indicator turns green, the charging is completed. 

The specific table below.

● The first use of the battery

Since the battery is not fully charged at the factory, please charge the 

new battery before use. Under normal circumstances, the battery when 

used for the first time, need to charge 4 hours, lithium-ion battery 

charging using slow charge or fast charge can be performed when 

07

08

Summary of Contents for RT53



















Reviews: