background image

Dismantling the Pump

1. Remove screw 1. (Picture

 3

)

2. Separate the motor housing 6 from the pump section. (Picture 

4

)

3. Unscrew nozzle 3 Take suction pressure valve 4 and pump plunger 8with spring 7 out of the

pump section..

Do not use force.

 (Picture

 5

)

4. Make the tightly fitting valve ball passable through piston opening with the aid of a copper

or brass pin. (Picture

 6

)

5. Place all parts in the appropriate solvent and clean them.

 Never use hard objects for cleaning!   Piston 8 (see spare parts) should move easily
 in the pump housing.

Assembling the Pump

Assemble the parts in the reverse order.
After cleaning, spray through the device briefly with resin-free oil as an anticorrosion measure.
Collect cleaning agents in an appropriate receptacle and dispose of in an appropriate manner.

EN Declaration of Conformity  CE

We declare at our sole responsibility that this product conforms to the following standards or
normative documents: “EN 50144-2-7:96, EN 55014-1:93+A1:97. EN 61000-3-
2:95+A13:97+A1:98+A2:98, EN 61000-3-3:95

                                                                                                                                                              5

Garantie

The appliance is guaranteed for six months subject to the enclosed terms and on condition that
it is 

only used for processing products approved for the food industry.

The appliance must not be operated continuously for longer than 10 minutes at a time.
The guarantee is based on 50 hours of use within a 6-month period.
Only 

original

 spare parts may be used in the event of repairs.

The appliances must be serviced and cleaned as described in the operating instructions.
The guarantee becomes valid with the delivery of the product to the end user.
The duration of the guarantee shall be determined by the end user‘s date of purchase. The
guarantee excludes any damage due to natural wear, overloading or incorrect handling.

Repairs

 not covered by the guarantee shall be performed by service centres subject to the

applicable price and delivery terms of the country in question.

Product liability

No liability is accepted for damage caused directly or indirectly by the use and spraying of
products. The user assumes full responsibility for the use of the product in accordance with the
laws of food hygiene and other legal regulations.

Pavel Vokatý

Summary of Contents for Gun 25









Reviews: