background image

User’s Manual Electric Bike

Congratulations on your purchase of this Retrospec electric bike. It has been carefully 

designed and manufactured according to the latest international quality standards.

Please read this instruction manual carefully and thoroughly before riding. It contains 

important information on safety, and maintenance. It is the owner’s responsibility 

to read this manual before riding. Keep this manual for future reference. This user’s 

instruction manual includes two sections: 

SECTION I - Mechanical Operation, and SECTION II - the Electric Operation. 

These instructions apply to electric bike models with following equipment:

Section I: Mechanical Components Operation

• 

Disc Brakes

Section II: Electrical Components Operation

• 

Battery-pack behind the seat tube

• 

Rear hub motor

• 

Controller integrated to the battery-pack

• 

Handlebar-mounted Display Panel operations.

Warranty: Should any original component prove defective in terms of workmanship 

within its warranty period, we will replace it. Warranty period for Retrospec electric 

bikes is as follows:

Electrical Components excluding Battery: 2 years with proper maintenance

Battery: 1 year

Frame and Fork: 1 year

All other components: 6 months

This warranty does not include labor and transportation charges. The company cannot 

accept any responsibility for consequential or special damage. This warranty applies 

only to the original retail purchaser who must have a proof of purchase in order to 

validate any claim. This warranty applies only in the case of defective components and 

does not cover the effects of normal wear, nor damage caused by accident, abuse, 

excessive loads, neglect, improper assembly, improper maintenance or the addition of 

any item inconsistent with the original intended use of the bicycle. 

No bicycle is indestructible and no claims can be accepted for damage caused by 

improper use, competition use, stunt riding, ramp jumping and leaping or similar 

activities. Claims must be submitted through your retailer. Your statutory rights are not 

affected. The company reserves the right to change any specification without notice. 

All information and specifications within this manual are correct at time of printing. 

1.  Tire/Tube

2.  Rim

3.  Spoke

4.  Disc brake

5.  Fork

6.  Mudguard

7.  Front light

8.  Head tube

9.  Stem

10.  Display Panel

Fig. 1 Electric Bicycle

Name of Pedal Electric

Assistance Bicycle Components

1

2

11.  Saddle

12.  Seat Post

13.  Frame

14.  Pedals

15.  Chainwheel/Crankset

16.  Chain

17.  Rear Light

18.  Kickstand

19.  Hub Motor

20.  Rear Carrier

21.  Battery

Summary of Contents for Jax












Reviews: