Operating the machine
30
5.15 Store functions
Pos : 8. 55 /00005 Ü berschrif ten/ 1. 1. 1 Ü bersc hrift en/ 111 Programme s peic hern @ 0\ mod_1229424145211_9.doc @ 5124 @ @ 1
5.15.1 Saving programs
Pos : 8. 56 /00010 Bedi enungsanleit ung en Kapitels ammlungen/ GM200 (2010)/ 0015 GM200N Bedienung/ 1590 GM 200_2010 Modul Progr amme speichern @ 3\mod_1279722274919_9. doc @ 21694 @ @ 1
•
Keep the button
E1
,
E2
or
E3
pressed until the segment displays no longer
flash.
The values for time and speed as well as the setting for REVERSE and INTERVAL
operation are stored in the memory of the corresponding button.
Fig. 13: Memory buttons
Pos : 8. 57 /00005 Ü berschrif ten/ 1. 1. 1 Ü bersc hrift en/ 111 St arten eines g es peic her ten Programms @ 0\ mod_1229424036698_9. doc @ 5118 @ @ 1
5.15.2 Starting a saved program
Pos : 8. 58 /00010 Bedi enungsanleit ung en Kapitels ammlungen/ GM200 (2010)/ 0015 GM200N Bedienung/ 1595 GM 200_2010 Modul St art en ei nes ges peichert en Pr ogramms @ 3\ mod_1279722524325_9. doc @ 21712 @ @ 1
•
Press the
E1
,
E2
or
E3
button.
The last saved values appear on the “TIME“ and “SPEED“ segment displays. The
LEDs above the REVERSE and INTERVAL buttons light up depending on default.
Press the START button to start grinding with the default parameters.
Pos : 8. 59 /00005 Ü berschrif ten/ 1. 1 Ü bersc hrift en/ 1. 1 Übersc hrift en BD A/ 11 Start
– Pause – Stop @ 3\mod_1279719602650_9.doc @ 21525 @ @ 1
5.16 Start
– Pause – Stop
Pos : 8. 60 /00010 Bedi enungsanleit ung en Kapitels ammlungen/ GM200 (2010)/ 0015 GM200N Bedienung/ 1596 GM 200_2010 Modul St art - Pause - St op @ 3\ mod_1279722525044_9. doc @ 21721 @ @ 1
5.16.1 Pause function
•
Press the STOP button during grinding.
Grinding is interrupted and the hood remains closed.
It is not possible to move the set parameters (speed, time, interval, reverse). The
current time display is suspended.
•
Press the START button to continue grinding.
Grinding is restarted and the time display runs again.
5.16.2 Premature termination of grinding
•
Press the STOP button during grinding.
Grinding is interrupted and the hood remains closed.
•
Press the STOP button again.
The device is switched off and the hood opens automatically. The parameters
chosen for grinding (speed, time, interval, reverse) are displayed.
Pos : 8. 61 /00005 Ü berschrif ten/ 1. 1 Ü bersc hrift en/ 1. 1 Übersc hrift en BD A/ 11 Überlas tsic her ung z urüc ks etz en @ 3\ mod_1279719797635_9. doc @ 21533 @ @ 1
5.17 Resetting the overload protection
Pos : 8. 62 /00010 Bedi enungsanleit ung en Kapitels ammlungen/ GM200 (2010)/ 0015 GM200N Bedienung/ 1598 GM 200_2 010_TM 100_M odul Ü berlast sicherung z urüc ksetzen @ 3\ mod_1279722532575_9.doc @ 21811 @ @ 1
The overload protection switch (
K
) is situated on the rear panel.
E1; E2; E3
