background image

12

Installation and Operation
Blood Bank Refrigerators

14 Warranty

14.1 Domestic Warranty

13 Months Full Warranty, Parts and Labor
United States of America and Canada

Revco Scientific, Inc. warrants this product to the owner for a 
period of thirteen (13) months from date of shipment by Revco 
Scientific, Inc. Under this warranty, Revco, through its 
authorized service organizations, will repair, or at its option, 
replace any part found to contain a manufacturing defect in 
material or workmanship without charge to the owner for parts, 
service labor, or any shipping or cartage costs. Replacement or 
repaired parts will be warranted for only the unexpired portion of 
the original warranty. This warranty is limited to products 
purchased and installed in the United States of America and 
Canada. It does not apply to damage caused by accident, misuse, 
fire, flood, or acts of God. It does not apply to damage caused 
from failure to properly install, operate, or maintain the product 
in accordance with the printed instructions provided.

To obtain prompt warranty service, simply contact the nearest 
authorized service center or dealer listed in the directory 
enclosed with each product. Revco’s own shipping records 
showing date of shipment shall be conclusive in establishing the 
warranty period.

This warranty is in lieu of any other warranties, expressed or 
implied, including merchantability or fitness for a particular 
purpose. The owner agrees that Revco’s sole liability with 
respect to defective parts shall be as set forth in this warranty, 
and any claims for incidental or consequential damages are 
expressly excluded.

14.2 International Warranty

16 Month Parts Warranty

Revco Scientific, Inc., warrants this product to the owner for a 
period of sixteen (16) months from the date of shipment by 
Revco. If any part is found to contain a manufacturing defect in 
material or workmanship, Revco assumes no responsibility for 
any labor expenses for service, removal, or reinstallation 
required to replace part, or for incidental repairs, and such costs 
are the responsibility of the Owner unless a service labor 
agreement exists between the Owner and his Dealer.

The warranty does not apply to damage caused by accident, 
misuse, fire, flood, or acts of God, or to defects resulting from 
failure to properly install, operate, or maintain the product in 
accordance with the printed instructions provided.

To obtain prompt warranty service. simply contact the Dealer 
from whom you purchased the product or the nearest Dealer 
handling Revco products. Revco’s own shipping records 
showing date of shipment shall be conclusive in establishing the 
warranty period.

This warranty is in lieu of any other warranties, expressed or 
implied, including merchantability or fitness for a particular 
purpose. The owner agrees that Revco’s sole liability with 
respect to defective parts shall be as set forth in this warranty, 
and any claims for incidental or consequential damages are 
expressly excluded.

14.3 Extended Warranty Options

In addition to Revco’s standard 13-Month full warranty on the 
complete product (USA and Canada), Revco can supply an 
additional four year protection on compressor and compressor 
parts. This additional coverage must be purchased at the time of 
original product purchase. Under this contract, Revco Scientific 
agrees to furnish a compressor FOB our factory to replace one 
which has been determined to be defective by Revco or a factory 
authorized Revco Service Agency.

Description

Catalog 

No.

Extended Four-Year Compressor Parts Contract, all 

refrigerators.

6069

Extended 12-Month Comprehensive Coverage, for all 

models, provides additional 12-month warranty 
coverage, parts and labor. Contact Revco for details.

6613

Summary of Contents for REB-1204














Reviews: