background image

9

Installation and Operation
Blood Bank Refrigerators

11 Cleaning

11.1 Cleaning the Drawers and Cabinet Interior

To clean the drawers and cabinet interior, remove the drawers 
following the instructions in Section 5. Use a solution of water 
and a mild detergent. Rinse the drawers and wipe them dry with a 
soft cloth.

11.2 Cleaning the Condenser

WARNING!

 Disconnect equipment from main 

power before attempting any maintenance to 
equipment or its controls.

CAUTION!

Condensers should be cleaned at least 

every six months. In heavy traffic areas, condensers 
load with dirt more quickly. Failure to keep the 
condenser clean can result in equipment warm-up or 
erratic temperatures.

CAUTION!

Never clean near condensers with your 

fingers. Some surfaces are sharp.

Periodically check the condenser to make sure that it is clean.

In all models, the condenser is located in the top machine 
compartment. To clean the condenser:

1. Disconnect the power.
2. Remove the top grill.
3. Use a vacuum cleaner with hose and brush attachments to 

clean the front face of the finned surface.

4. Clean up any loose dust and replace the grill.
5. Reconnect the power.

Summary of Contents for REB-1204














Reviews: