English
8A Insert a memory card:
To record videos, the micro-SD memory card must be
inserted. The card must be inserted carefully in the slot on the left side of the
camera
1F
with the contacts facing to the front and upwards until it engages.
Do not use force, otherwise the camera or the memory card could be damaged.
Only standard micro-SD memory cards can be used, HC cards are not supported.
8B Remove the memory card:
To remove the micro-SD memory from the camera,
press on the memory card. There is an audible, quiet click and the card is pushed
out half way. It can then be pulled out completely using fingers.
8C Read the memory card:
Then insert the micro SC memory card in a USB card
reader and connect it to a USB port of a computer. After a short installation routine,
the computer is ready to download the data from the model. Please follow the
appropriate procedure for your computer system.
8 MEMORY CARD
7 FLIGHT CONTROL
The model is equipped with an automatic altitude control assistant that makes it possible
to learn how to control the model quickly and easily. The assistant is a sensor that can
measure the air pressure to within 10 centimetres of the exact altitude and thereby
automatically keep the quadrocopter at the specified altitude. Therefore, beginners can
concentrate on forward/backwards and banking.
Attention:
Due to outside influences, the pressure inside the model may change,
causing the model to automatically rise or lower. This is not a defect. Briefly actuating
the control for thrust and rotation
2A
is sufficient to counteract this.
Note:
Only minimal corrections of the controls are necessary for a smooth flying behavior
of the model! The direction indication applies when the model is viewed from behind. If
the model is flying forwards towards the pilot, it must be moved in the opposite direction.
Switch on the model as described in section 5.
7A
In order to lift off, press the button for lift-off
2M
.
7B
In order to land, press the button for landing
2N
.
7C
In order to gain altitude, carefully move the control for thrust and rotation
2A
forwards.
7D
In order to fly at a lower altitude, move the control for thrust and rotation
2A
back.
7E
Fly forward by moving the controller for forward/backward and sideways
flight
2B
carefully forward.
7F
Fly backward by moving the controller for forward/backward and sideways
flight
2B
carefully backward.
7G
Fly to the left by moving the controller for forward/backward and sideways
flight
2B
carefully to the left.
7H
Fly to the right by moving the controller for forward/backward and sideways
flight
2B
carefully to the right.
7I
Turn the model around to the left by moving the control for thrust and rotation
2A
to the left.
7J
Turn model around to the right by moving the control for thrust and rotation
2A
to the right.
English
2D Photo button:
A photo is taken by pressing the button.
2P Video button:
Video button: A video is recorded by pressing the video button
(the LEDs
1C
begin to blink). Pressing the button again stops the recording and the
LEDs
1C
illuminate continuously again. Only recordings that are stopped with this
button are saved.
2G Turbo button:
The lowest speed is activated when the model is switched on. By
pressing the button twice, the medium level is activated and the remote control
issues two short beeps. By pressing again, the remote control issues three short
beeps for the highest speed. Pressing the button again returns to the lowest level.
Flip button:
A longer vertical press (about 2 seconds) of control
2I
activates the flip
function. The next movement with control
2C
allows the model to complete a 360°
flip in the corresponding direction. In the process, ensure a safety altitude of about 2
metres and a sufficiently charged battery.
2H Doubleclick on button for Headless Mode:
Headless mode supports beginners
in the initial stages. Regardless of where the quadrocopter turns, the direction of
flight always corresponds exactly to the direction specified with the control for
forwards/backwards and sideways movement
2I
. An example: If the model were
to be turned 180° and flown towards the operator, the operator would have to
„convert“ the forwards/backwards and sideways movement accordingly. This is no
longer necessary if headless mode is activated, as the internal processor always
converts the control directions automatically. The LEDs on the model always flash
briefly twice if headless mode is activated. Doubleclicking the
2H
button again
deactivates the mode.
Attention:
The model „notes“ the forwards direction during each switch-on. This
means that the operator must not turn when controlling the model, as this would
change the concept of „forwards“ and „right/left“ in relation to the model. If the operator
changes position and wants to use headless mode - or if the control direction is no longer
correct due to a collision, the model must be restarted.
The model must be switched on first in order to connect it to the remote control.
Its adjustment is simple, but it requires some patience and a feel for it. Please observe
the following instructions precisely: Carefully move the thrust control up and raise the
helicopter approximately 0.5 to 1 metre in altitude.
6 TRIM ADJUSTMENT OF THE CONTROL
6A If the model automatically moves slowly or quickly to the left or right ...
gradually press the trim for sideways flight
2K
in the opposite direction.
6B If the model automatically moves slowly or quickly forwards or backwards ...
gradually press the forwards/backwards trim
2J
in the opposite direction.
18
19
