English
English
4 CHARGING THE MODEL
Attention:
The battery and motor must cool down for 15 to 30 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
• Remove the battery from the model
4A
. Plug the USB charger into an open USB port
4B
. The status LED on the charger begins to illuminate continuously.
• Plug the battery plug into the charging socket of the charger, ensuring correct polarity
4C
. The battery must be gently inserted into the charging socket –
DO NOT USE FORCE. If the battery is not correctly inserted into the charging socket,
the battery may become damaged and, under certain circumstances, cause injury.
• The status LED on the USB charger goes out when the charging process starts.
• The charging process lasts approx.70-80 minutes and must be continuously
monitored. The status LED illuminates continuously as soon as the charging process is
finished.
• Disconnect the battery from the charger and disconnect the charger from the USB
port once charging is complete.
The model can fly for approx. 5-7 minutes after a charge time of approx.
70-80 minutes.
Warning notice:
The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
2 REMOTE CONTROL
2A
No function
2B
No function
2C
Control for thrust and rotation
2D
Photo button
2E
Power LED
2F
Antenna
2G
Turbo button
2H
Button for Headless Mode
2I
Control for forwards/backwards and
sideways flight
2J
Trim for forwards/backwards
2K
Trim for sideways
2L
ON/OFF switch
2M
Button for lift-off
2N
Button for landing
2O
Battery compartment cover
2P
Video button
2Q
Securing screw
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the remote control and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
Technical changes and differences in
color reserved!
Required batteries for the model:
Power supply:
Rated output:
1 x DC 3,7 V / 3 Wh
rechargeable
LiPo battery (included)
Capacity: 800 mAh
Battery requirement for the
remote control:
Power supply:
DC 6 V
Batteries:
4 x 1,5 V “AAA“
(not included)
1 MODEL
1A
Rotor shaft with main gear wheel
1B
Camera lens
1C
LEDs
1D
Battery compartment
1E
ON/OFF switch
1F
SD card slot
1G
Camera
5 START PREPARATION
The model must be switched on first in order to connect it to the remote control. To
do this, push the battery into the battery compartment
5A
on the model and connect the
battery plug with the battery connection cable. If the battery is not correctly inserted into
the charging socket, the battery may become damaged and, under certain circumstances,
cause injury. Do not use force and ensure the correct polarity.
To switch on the remote control, move the ON/OFF switch
2L
to ON
5B
.
Then switch the ON/OFF switch on the model
5C
to ON. Place the model on the
ground so that its tail points toward you
5D
. Press the button
2M
to lift off. The model
automatically climbs to an altitude of approximately 1m. Press the button
2N
to land.
Attention:
If the model does not land correctly, immediately move the control for
thrust and rotation
2C
to the bottom left and move the control for forward/backwards
and banking
2I
to the bottom right at the same time
5D
.
Tip:
The rotors can also be started and switched off manually. For this purpose, move
the control for thrust and rotation
2A
to the bottom left and move the control for
forward/backwards and banking
2B
to the bottom right at the same time
5F
.
Once you have finished flying, switch the model off first and then the remote control.
A A
A A
A A
A A
3 INSERTING BATTERIES (REMOTE CONTROL)
3A
Unscrew and remove the cover.
3B
Insert 4 x 1,5 V AA batteries and pay attention to the polarity,
as shown in the battery compartment.
3C
Close the battery cover and secure with the screw.
16
17
