background image

9

BATTERY PRECAUTIONS

SAFETY PRECAUTIONS

  ALWAYS disconnect the battery from the hexacopter when not in use.

  Only use the included charger with the flight battery.

  Do not attempt to use this charger with NiCd or NiMH battery packs.

  Do not attempt to use a damaged battery.

  This product contains a LiPo battery. Must be recycled or disposed of 

properly.

  Do not leave the charger unattended while charging. Disconnect the 

battery and unplug the charger immediately if either becomes hot! 
However, it is normal for the charger to get warm.

  Disconnect the battery from the charger and carefully move the battery 

to a fireproof location if the battery begins to swell or smoke!

  Never allow the battery temperature to exceed 140° F [60° C].

  Do not attempt to charge a battery if it is swollen or hot.

  Do not place the charger or any battery on a flammable surface or near 

combustible materials while in use.

  Never disassemble or modify pack wiring in any way or puncture cells.

  Never charge inside a vehicle.

  Always disconnect the battery and remove the charger from the USB 

port when not in use.

  Land your model immediately when the LEDs flash to indicate that the 

battery power is low. Recharge the battery before attempting another 
flight. A dangerous situation can occur when attempting to recharge an 
over-discharged battery!

  ALWAYS keep a supply of sand accessible when charging. Dumping sand 

on the battery will extinguish a LiPo chemical fire.

  ALWAYS KEEP OUT OF REACH OF CHILDREN

  Adult supervision required.

  Before flying, go to www.knowbeforeyoufly.org.

  Do not touch the spinning blades or fly over another person’s head.

  Keep your face and body as well as all spectators away from the rotors 

whenever the battery is connected.

  Stay clear of buildings, trees and power lines. 

AVOID

 flying in or near 

crowded areas. 

DO NOT

 fly close to people, children or pets.

  Maintain a safe pilot-to-hexacopter distance while flying.

  Your Nano Hexagon should not be considered a toy, but rather a small, 

working model. If not operated correctly, the model could possibly cause 
injury to you or spectators and damage to property.

  You must check the operation of the model before every flight to insure 

that the model has remained structurally sound.

  Do not alter or modify the model, as doing so may result in an unsafe or 

unflyable model. 

The Nano Hexagon uses a lithium polymer (LiPo) battery. Follow these precautions to insure safe and trouble-free operation.

Follow these safety precautions when operating this or any model hexacopter.

Summary of Contents for NANO Hexagon













Reviews: