background image

 

 

 

To cancel movement alarm:  

 

   

Command: password e.g. 

  nomove123456 

 

 

 

 

 

5.17 Over speed alarm: 

 

 

 

To activate: 

 

   

Command: speed+pspace+080

          (in km/h)   

 

Response: speed ok! e.g.  

speed123456 080

  

When the speed exceeds 80 km/h, it will send the following SMS to authorized numbers every 

3 minutes:  “speed+080!+location”

 

To cancel:  

 

  

Command: password  e.g. 

nospeed123456

 

 

 

 

5.18 SOS alarm  

 

 

TK102-NANO is equipped with an SOS button. In case of emergency, pressing this button 

will notify authorized numbers with three text message followed by a phone call. The SOS  

alarm is activated by default and the SOS button is enabled.  

 

To disable the SOS button: 

 

  

Command:  sos+pspace+off  e.g. 

sos123456 off  To enable the SOS button 

 

   

Command: sos+pspace+on e.g. 

  sos123456 on 

 

  

 

   

  

  

  

  

  

  

12

  

 

 

5.19 Low battery alarm  

Low battery alert helps users to know when the battery of TK102-NANO is low. It sends 3 

notifications to authorized numbers; at %10 , at %5 and just before it's completely flat.

 

 

Low battery alert is activated by default. To activate;  

Summary of Contents for TK102-NANO























Reviews: