Rexnord Falk Drive One DB Owner'S Manual Download

Page: 2 / 27

Owners Manual

•

Falk

™

Drive One

Enclosed Gear Drives

(Page 2 of 27)

Type D Series

•

Sizes M1130 thru M1210

168-050

Rexnord Industries, LLC, 3001 W. Canal St., Milwaukee, WI 53208-4200

January 2019

Telephone: 414-342-3131 Fax: 414-937-4359

Supersedes 04-11

e-mail: info@rexnord.com web: www.rexnord.com

(PN 2124650)

FOUNDATION, STEEL

— When mounting gear drive on

structural steel, it is recommended that an engineered

design be utilized for a pedestal,

adapter base or bed to provide

sufficient rigidity, to prevent

induced loads from distorting

the housing and causing gear

misalignment. In the absence

of an engineered design, it is

recommended that a base plate,

with thickness equal to or greater

than the thickness of the drive

feet, be securely bolted to steel supports and extend

under the entire drive as illustrated.

FOUNDATION, CONCRETE

— If a concrete foundation is

used, allow the concrete to set firmly before bolting down

the gear drive. For the

best type of mounting,

grout structural steel

mounting pads into

the mounting base, as

illustrated, rather than

grouting the drive directly into the concrete.
Motors and other components mounted on motor plates or

motor brackets may become misaligned during shipment.

ALWAYS check alignment after installation. Refer to page 5

for coupling alignment instructions.

Gear Drive Alignment

FOOT-MOUNTED DRIVES

– Align drive with driven

equipment by placing broad, flat shims under all mounting

pads. Jack screw holes are provided by mounting feet to

facilitate alignment. See Table 12, page 10 for fastener

and wrench sizes. Start at the low-speed shaft end and

level across the length and then the width of the drive.

Check with a feeler gauge to make certain that all pads are

supported to prevent distortion of housing when drive is

bolted down. After drive is aligned with driven equipment

and bolted down, align prime mover to drive input shaft.

Refer to page 5 for coupling alignment.

CONTINUOUS PLATE

LIFTING HOLES

2 PER CORNER

(16 TOTAL)

JACKING

SCREW HOLES

DIPSTICK/VENT

HOLES

JACKING

SCREW HOLES

DRAIN

PLUG

If equipment is received from the Factory mounted on

a bedplate, the components were accurately aligned at

the Factory with the bedplate mounted on a large, flat

assembly plate. Shim under the bedplate foot pads until

the gear drive is level and all feet are in the same plane.
Check high-speed shaft coupling alignment. If the

coupling is misaligned, the bedplate is shimmed

incorrectly. Re-shim bedplate and recheck high-speed

coupling alignment. If necessary, realign motor.

Shaft-Mounted Drives – General

Shaft-mounted drives should never be mounted in a

manner that restricts the natural movement of the drive.

They should be allowed to move freely with the shaft on

which it is mounted. Shaft-mounted drives should always

be used in conjunction with a torque reaction arm. Refer

to Appendixes A, B or C for torque reaction arm mounting

instructions and angular limits. The drive may require

repositioning on the driven shaft after initial installation to

accommodate the location of the foundation anchor and

be within limits specified in Appendix A (fixed torque arm)

or Appendix B (adjustable torque arm).
The tapered bore hollow shaft is designed for use with a TA

Taper

bushing for mounting the drive on a driven shaft

with a straight outside diameter. The taper bushing

assembly is supplied with a thrust plate kit and retention

fastener as standard (usage is optional, shaft cover must

be removed to install thrust plate kit). Refer to data sheet

supplied with the tapered bushing assembly for driven

shaft length, shaft keyway length and driven shaft tapped

hole dimensions if the thrust plate kit with retention

fastener is to be used.
Prior to installing the drive, it is a good idea to check

the driven shaft for proper dimensions. Using Table

1 or 1A, find the driven shaft size for the application.

Verify that dimensions A and B are within the allowable

range. When dimensions are verified, proceed with the

installation. The minimum and maximum driven shaft

engagements, dimension N in Figure 1, are shown in

Table 2. The minimum engagement is necessary for full

bushing engagement, and the maximum (and specified)

engagement is provided for use when the thrust plate kit is

used for added retention capacity and an auxiliary removal

aid (bushing nut normally used for both).

LEVELING

REFERENCE

SURFACES

SHIMS

KEEP CLOSE

BUSHING NUT

DRIVEN SHAFT

BEARING

SUPPORT

THRUST

PLATE

BORE

INPUT

SHAFT

SHEAVE

Figure 1

Summary of Contents for Falk Drive One DB




























Search results

Summary of Contents for Falk Drive One DB

Reviews:

Related manuals for Falk Drive One DB

Brands by name

Popular brands

Rexnord Falk Drive One DB, Owner'S Manual

Search results

Summary of Contents for Falk Drive One DB

Reviews:

Related manuals for Falk Drive One DB

Brands by name

Popular brands