Rexnord Falk Drive One DB Owner'S Manual Download

Page: 21 / 27

Falk

™

Drive One

Enclosed Gear Drives

•

Appendix E

Type D Series

•

Sizes M1130 thru M1210

(Page 21 of 27)

Rexnord Industries, LLC, 3001 W. Canal St., Milwaukee, WI 53208-4200

168-050

Telephone: 414-342-3131 Fax: 414-937-4359

January 2019

e-mail: info@rexnord.com web: www.rexnord.com

Supersedes 04-11

(PN 2124650)

Electric Fan Installation & Maintenance

Installation

The installation and troubleshooting of electric cooling fans

are to be carried out by a qualified electrician according

to the applicable local, state, province and federal codes.

Inspect for any damage that may have occurred during

transit. Check all bolts, screws, set screws, etc. Retighten

as required. Before installing, rotate the blade to be sure it

does not rub. Adjust if necessary. Before installation, read

the entire manual carefully.
This guide is pertinent only to electric fans furnished by the

Factory and manufactured by Multifan Inc. (can be verified

from nameplate on the electric fan). In the event the

electric fan furnished by the Factory is of a special nature

(manufactured by an alternate fan manufacturer), please

contact the Factory for appropriate electric fan installation

and maintenance instructions.

General Safety Information

Warning

: To reduce the risk of fire, electric shock, or

personal injury, observe the following:

1. Use this electric fan only in the manner intended by

the manufacturer. If you have any questions, contact

Factory.

2. Before servicing or cleaning the fan, switch the power

off at the service panel and lock out to prevent the

power from being switched on accidentally.

3. Follow all local electrical and safety codes, as well as

the National Electrical Code (NEC) and Occupational

Safety and Health Act (OSHA).

4.  Fan motor must be securely and adequately grounded.
5.  All working parts should be grounded.
6.  When cleaning electrical equipment always use an

approved cleaning agent. See CLEANING in NOTES

section, page 22.

7. For general ventilation and cooling use only. Do not

use if hazardous or explosive materials and vapors are

present.

Guidelines For Installation

Before connecting the electric fan, check if the information

on the fan motor name plate is in accordance with the

actual main supply voltage, phase and frequency.

Warning

: To reduce the risk of fire, electric shock, or

personal injury, observe the following:

1. Switch off the main power supply and lock out before

installing, servicing or making connections to the fan.

2. Installation work and electrical wiring must be done by

a qualified person(s) in accordance with all applicable

codes and standards, including fire-rated construction.

3. The fan should be securely mounted. Recheck the

mounting hardware and tighten as necessary.

4. The fan motor must always be grounded. The

installation of a motor protection switch is

recommended. See Figure 1 for wiring diagrams.

5. Mount the motor guard if removed. The motor guard

must be installed at all times during operation to prevent

injury to personnel by rotating fan blade.

6. Use liquid tight electrical fittings and conduit.

SINGLE PHASE

TYPE - E

1 PHASE 220V - 50Hz

1 PHASE 110V - 60Hz

1 PHASE 220V - 60Hz

1 PHASE 240V - 60Hz

CAPACITOR

THERMAL

PROTECTON

N (L2)

SINGLE PHASE

TYPE - D

3 PHASE

3 PHASE 220/380V - 50Hz

3 PHASE 230/400V - 50Hz

3 PHASE 240/415V - 50Hz

3 PHASE 220/380V - 60Hz

3 PHASE 208/360V - 60Hz

3 PHASE 265/460V - 60Hz

250V

10A

COS

ψ=1

OPTION

THERMAL

PROTECTION

250V

10A

COS

ψ=1

OPTION

Figure 1

Summary of Contents for Falk Drive One DB




























Search results

Summary of Contents for Falk Drive One DB

Reviews:

Related manuals for Falk Drive One DB

Brands by name

Popular brands

Rexnord Falk Drive One DB, Owner'S Manual

Search results

Summary of Contents for Falk Drive One DB

Reviews:

Related manuals for Falk Drive One DB

Brands by name

Popular brands