Rexnord Smart Condition Monitoring System 1050 Instruction Manual Download

Page: 4 / 14

Smart Condition Monitoring System Electrical and Communications Manual

Electrical Connection

CONNECTING AC INPUT POWER TO SCMS AC POWER SUPPLY UNIT

(See item 23 in

)

The Smart Condition Monitoring System Edge device power supply unit must be connected to AC power
to operate. The input power specifications include:

• Nominal voltage: 100V to 240V ac nominal 50-60Hz

• Maximum power: 120 Watts

Figure 2 — Drawing of third generation Smart Condition Monitoring System Serial Edge Device showing

variant with optional cellular antenna.

Figure 3 — Serial Edge Device showing all available user connections.

9.96

9.41

3.54

4X 0.26

8.64

7.87

2.68

4X 0.50

LAN

WAN

Status

LED

Port 1

24V dc

Power

Port 2

Summary of Contents for Smart Condition Monitoring System 1050















Search results

Summary of Contents for Smart Condition Monitoring System 1050

Reviews:

Related manuals for Smart Condition Monitoring System 1050

Brands by name

Popular brands

Rexnord Smart Condition Monitoring System 1050, Instruction Manual

Search results

Summary of Contents for Smart Condition Monitoring System 1050

Reviews:

Related manuals for Smart Condition Monitoring System 1050

Brands by name

Popular brands