background image

16

Operation and mechanisms

Operation and mechanisms

Operation: general points

 

See under 'Installation' (manual opening and closing). 

 

†

Caution : please note dampers must be fully open before starting supply and/or extract fans.

 VA DP MEC Mechanism for motorised unlocking and resetting.

Mechanism for the motorised unlocking and resetting of the Smoke Control Damper Avantage DP, Kamouflage DP.

1.  Motor and housing
2.  Motor mounting bracket
3.  Drive arm guide pin
4.  Motor drive arm
5.  Cable connectors

4

2

1

3
5

Unlocking

 

manual unlocking

: manual release with the damper key (delivered in the bag together with the installation guidelines)

 

remote unlocking

: remote by connection of 24 V DC

Resetting

 

manual resetting

: rearm magnetic latch with key (delivered in the bag together with the installation guidelines), press the drive 

linkage arm to unlock position and pull the damper closed

 

motorised resetting

: remote resetting by inverting the voltage connection

Electrical connection

VA DP MEC

DC

FC

M

DC

FC

M

DC

FC

M

DC

FC

DC : 

Switch closed position smoke evacuation shutter

FC : 

Switch open position smoke evacuation shutter

black

gre

y

blue

black

gre

y

blue

br

own

blue

24VDC

24VDC

24VDC

MEC

Nominal voltage 

motor

Nominal voltage 

magnet

Power consumption 

(stand-by)

Power consumption 

(operating)

Standard switches

Protection class

VA DP MEC

24 V DC

N/A

N/A

Pnom 15VA

1mA...6A, DC 5V...AC 250V

IP 32

Summary of Contents for AVANTAGE DP




















Reviews: