RFL 9508
RFL Electronics Inc.
June 2005
4
Channel Density
Maximum telephony channels:
•
Up to 8 FXS, FXO or E&M
Maximum data channels:
•
Up to 4 serial data ports with optional serial port
extender chassis
Telephony Features
Voice compression algorithms (5 channels per DSP):
•
ACELP-CN (8K/6K with fallback), G.711 (PCM
64K), G.723.1 (Low 5.3K/High 6.3K), G.726,
(ADPCM 16K/24K/32K/40K), G.729 and
G.729a (8K)
•
FAX Relay: Group III FAX 4.8, 7.2, 9.6,12.0, 14.4 Kbps
Modem Relay:
•
V.32bis demodulation up to 14.4Kbps, modem pass
through (G.711)
•
Any-to-any switching, using PowerCell over PVC or
Frame Relay SVC, or SIP (Session Initiated Proto-
col) VoIP, including end-to-end QSIG/ISDN support
for supplementary services
Analog telephony channels:
•
FXS: loop and ground start, forward disconnect, caller
ID and billing tone generation
•
FXO: loop start, forward disconnect and caller ID de-
tection
•
E&M: immediate and wink start, custom
Digital telephony channels:
•
Digital CAS Signaling types: Immediate, Wink, FXO,
FXS, FXO ground, FXS ground, E1/R2, PLAR, cus-
tom
•
Pulse and tone dialing
•
Voice traffic routing with alternates destinations and
digits manipulation using local mapping tables, lo-
cally switched TDM calls (hairpin)
•
VoIP peer-to peer calling with ingress and egress di-
aling plan, centralized dialing plan using SIP Redi-
rect, and registration to optional SIP proxy
LAN Support
•
Two independent fully routed 10/100BaseT ports, two
IP address per port
•
Ethernet interfaces: Ethernet II and IEEE 802.2, 802.3,
SNAP
Network Management
•
SNMP management via Network Management Sys-
tem (NMS).
•
Menu driven async console port (VT-100) via DB9
male connector, auto-sensing DTE/DCE
•
Remote Telnet access to command port
RFL 9508D UCC
UCC System Details
Standalone base unit with 19" rack mount
•
One V.35 universal serial port (link)
•
Two 10/100BaseT Ethernet (RJ45 connectors)
•
3 expansion slots for interface cards
Available Interface Modules
Analog telephony interface cards:
•
2 and 4-port FXS modules with on-board DSP, (RJ11
connector)
•
2 and 4-port FXO modules with on-board DSP (RJ11
connector)
•
4-port E&M module with on-board DSP (2 or 4 wire,
types I, II, or V, 600 ohms, RJ48 connectors)
Data interface cards:
•
2-port universal serial WAN interface, DTE or DCE,
compatible with RS-232/V.24, V.35, X.21/V.11, RS-
449/V.36, RS-530, internal/external clocking
Link Port Protocols
Power Lines:
•
Serial synchronous full duplex , Frame Relay, HDLC
and PPP, PowerCell
•
IP WAN
Any-to-Any Voice Switching
The RFL 9508D UCC integrates the disparate phone sys-
tems of individual sites, eliminating the need for consistency
increasing flexibility. With support for both analog and digital
voice, and legacy and packet data, the RFL 9508D UCC sup-
ports all the networking needs of the Distributed Power Net-
works.
Simplified Network
Management
Utilizing versatile software the RFL 9508D UCC is easy to
configure and manage, integrating with multi-vendor network
management systems via SNMP-compliant MIBs and user-
friendly Windows graphical management.
Supports Industry Standards
Seamless interconnectivity is not limited to voice, however,
the RFL 9508D UCC also offers flexible data protocol support
and interfaces with a wide range of network services and user
requirements.
Network Connections
•
Network Topology: mesh, hierarchical, star, point-to
point,
•
Automatic node discovery and rerouting with least
cost metric routing
September 2007
