background image

Copyright, RFXCOM 2021

 

RFXtrxLAN Rev. 2.0 

page 14 / 14 

11.  Warning: 

 

RF signals are possible disturbed, and it has not been justified for this equipment at uses in 
circumstances where life-threatening or dangerous situations are possible. 

 

RFXCOM HARDWARE AND SOFTWARE IS NOT INTENDED FOR USE IN THE OPERATION 
OF NUCLEAR FACILITIES, AIRCRAFT NAVIGATION OR COMMUNICATION SYSTEMS, AIR 
TRAFFIC CONTROL SYSTEMS, LIFE SUPPORT MACHINES OR OTHER EQUIPMENT IN 
WHICH THE FAILURE OF THE SOFTWARE COULD LEAD TO DEATH, PERSONAL INJURY, 
OR SEVERE PHYSICAL OR ENVIRONMENTAL DAMAGE. 

12.  License 

 

You are allowed to use RFXCOM software, protocols and Written Materials with RFXCOM 
hardware only.  

 

All copyright and other proprietary notices associated with RFXCOM software, protocols and 
Written Materials shall be visible to all users. 

 

You may not sell, distribute, loan, rent, lease, license, sublicense or otherwise assign or transfer 
RFXCOM software or RFXtrx protocols or Written Materials unless expressly authorized in writing 
by RFXCOM. 

 

You may not use any RFXCOM device, software or protocol as part of an exclusive or patented 
product without the express prior written permission of RFXCOM. 

 

You may not alter, modify, adapt or create derivative works based on any part of RFXCOM 
software or protocols or Written Materials in any way, including translating, reverse engineering, 
disassembling or decompiling the software. 

13.  Copyright notice 

 

All RFXCOM hardware, software, protocols and Written Materials are protected by copyright laws, 
and may not be reproduced, republished, distributed, transmitted, displayed, broadcast or 
otherwise exploited in any manner without the express prior written permission of RFXCOM. 

 

Netherlands Copyright and international treaty provisions protect the SOFTWARE, HARDWARE, 
RFXtrx protocols and Written Materials and shall be subject to the exclusive jurisdiction of the 
Netherlands Courts  

 

RFXCOM reserves all rights not expressly granted herein. 

14.  Revision History 

Version 0.0  October 7, 2021 

Initial version 

Version 1.0  October 25, 2021 

Installation of RFXtrx433E added 

Version 2.0  November 5, 2021 

Don’t use USB added 
Restore factory setting text added 

Summary of Contents for 21201















Reviews: