background image

 

DTR_314-01-01-001_EN_d

 

1.

 

Specifications  

The display for weighing scales WA-1 MINI 

Dimensions: 

1

404mm x 151mm x 40mm / 15.9in x 5.9in x 1.6in 

Digit height: 

60mm / 2.4in 

Permissible input voltage range (long-term): 

100 ÷ 240 VAC 

Permissible input voltage range (short-term): 

85 ÷ 264 VAC 

Acceptable input voltage frequency range: 

47 ÷ 63 Hz 

Device operation temperature (ambient): 

-25°C ÷ 45°C \ -13°F ÷ 113°F 

Device operation temperature (device surface): 

-25°C ÷ 60°C \ -13°F ÷ 140°F 

Average power consumption: 

5W 

Casing tightness rating

2

 IP: 

66 

Device weight: 

1.5kg \ 3.3lbs 

2.

 

Transport and storage 

The  device  is  sensitive  to  mechanical  damages.  Care  should  be  taken  to  properly  protect  the  device  during 
transport  so  as  to  eliminate  any  damage.  It  is  forbidden  to  transport  the  device  components  separately  in  a 
collective package – each component must be packed separately and cannot 'bump' during transportation.  

Due  to  protective  packaging,  the  device  should  be  stored  in  the  temperature   -25°C  ÷  +60°C  [-13°F  ÷  140°F] 
at the humidity below 99%RH. 

 

3.

 

Device construction  

WA-1 MINI has a housing made of polycarbonate, which is resistant to UV radiation and has a high mechanical 
strength. By using the thermo-moulded housing and a rear sealing layer, the device, when properly assembled, 
meets the IP66 tightness requirements. The display can also operate at the temperatures from -20°C to + 60°C. 

3.1

 

WA-1 MINI construction  

The figure shows display for weighing scales WA-1 MINI

3

 

Front view 

Side view 

 

det. A

 – Prestige line housing; 

det. B

 – display; 

det. C

 – mini extender plate; 

det. D

 – mounting the bracket holder; 

det. E

 – power supply 

unit; 

det. F

 – mounting bracket  

Fig. 1 

3.1.1

 

List of display cables  

1.  Five-metre power cord (2 x 0.5mm² [2x18AWG], core markings: blue, brown), terminated with WAGO 222-412 
connectors on each core,  
2.  Five-metre signal cable (2 x 0.5mm² [2x18AWG], RS232 interface; core markings: white -> RA, green -> RK), 

                                                           

1

 Integrated roof 55mm. 

2

 Specified on the basis of EN 60529. 

3

 Explanatory figure.

 

Summary of Contents for KAZEL WA-1 MINI









Reviews: