background image

CUSTOMER SERVICE

If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the address above. Include

the product model number, color, and a brief description of the part. Call 1-800-762-1751.

CARE AND CLEANING

DO NOT

 scratch or chip the finish. 

DO NOT

 use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth.

Blot spills immediately and wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully package all original

hardware to protect from loss.

TOOLS AND INSTALLATION

Tools Necessary: Allen Key (included)

NOTE

: It may be easier to assemble product with two people.

NOTE

: When inserting bolts, turn clockwise until tight. Then loosen 

1

2

 - 

3

4

  of a turn. After crib is completely assembled, return to each bolt and

tighten. Use wax or soap on all bolts to facilitate assembly

WARNING:

 Read all

instructions before assembling this

product. 

KEEP INSTRUCTIONS

FOR FUTURE USE.

Page  1  of  12

All Restoration Hardware cribs are designed to meet the highest safety

standards and comply with all U.S. and Canadian cribs and cradles regulations.

Made in Vietnam

Distributed in the U.S.A. by:

Restoration Hardware Baby & Child

2900 North Macarthur Dr. Tracy,

CA95376, USA

www.rhbabyandchild.com

Distributed in Canada by:

Restoration Hardware Canada, Inc.

1500-1055 West Georgia Street

Vancouver, British Columbia V6E4N7

Summary of Contents for VERSAILLES CONVERSION CRIB













Reviews: