background image

2/7

IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS

·

The mattress intended for use on the bed shall be a full-size crib

mattress having minimum dimensions of 51-5/8 inches (1310mm) in

length, 27-1/4 

 

inches (690mm) in width and 4 inches (100 mm) in

thickness, not 

 

exceeding 6 inches (152 mm) in thickness.

·

If guardrails are used as the mattress containment means,

guardrail(s) provided must be used to avoid the formation of a gap

between the 

 

mattress and the bed that could cause an entrapment.

·

DO NOT

 place bed near windows where cords from blinds or drapes

may strangle a child.

·

DO NOT 

place items with a string, cord, or ribbon around a child’s

neck, such as hood strings or pacifier cords.

·

DO NOT

 suspend strings over a toddler bed for any pacifier cords.

·

A child using the toddler or day bed shall be at least 15 months of age

and shall not weigh more than 50lbs (22.7kgs).

WARNING: ENTRAPMENT / STRANGULATION HAZARD

Infants have died in toddler beds from entrapment and strangulation.

Failure to follow these warnings and the assembly instructions could

result in serious injury or death.

NEVER

 use bed with children under 15 months.

NEVER

 place bed near windows where cords from blinds or drapes

may strangle a child.

Summary of Contents for ZOE TODDLER BED








Reviews: