background image

RHG Products Company 

Filter Replacement Schedule & Procedure 

Your carbon filter protects your system from damaging chlorine and 

water disinfection agents. It is recommended that you change your 

carbon filter cartridge every 6 months. Failure to do so will void your 

warranty. Order RHG #20066-C.  

Your DI filter has a limited lifespan based on the amount of dissolved 

solids it is removing from the water. DI filter cartridges need to be 

replaced as needed for your cleaning application.  

Order RHG #20066-D. 

 

To change your filter cartridge, first disconnect any hoses from the 
elbow in the insert at the top of the filter housing. Remove the stainless 

steel U-Pin. Depress the insert into the housing 

slightly

. Filter inserts can 

be pried out using the stainless U-Pin. (See diagram included in this 

literature) Remove the spent filter cartridge and replace. 

 

To install the new filter, put the new filter into the housing the same 

way the previous one was installed.  There is an o-ring on the filter.  

This o-ring should go at the top end of the housing.  Insert the filter from 

the opposite end first.  Be sure to run water through the system without 

any booster motor/pump assembly powered on to purge all air out of 

the system before or you risk damaging the filters. 
 

Reassemble filter housing and reconnect hoses. You may need to 

relubricate your filter housing insert to ensure a tight seal. Use a silicone 

valve stem lubricant. RHG uses Dow Molykote 111. Flush new carbon 

filter cartridge if needed.  

 

RO membranes have a much longer service life and in the experience of 

RHG may last the life of the system. However ROs are only warrantied 

for factory defect and may eventually diminish in performance or fail. If 

you experience a reduction in RO performance in your H2Pro system, 
contact RHG directly to troubleshoot.  

 

RO MEMBRANES SHOULD NOT BE ALLOWED TO DRY OR COLLECT STAGNANT 
WATER IN THE BOTTOM OF THE MEMBRANE. THIS WILL DIMINISH 

PERFORMANCE, POTENTIALLY TO THE POINT OF FAILURE. TO PREVENT THIS, 

ROs SHOULD BE RUN ON A REGULAR BASIS, AT LEAST EVERY TWO WEEKS, AFTER 

FIRST USE, EVEN DURING “OFF-SEASON”.  

Summary of Contents for H2PRO












Reviews: