background image

Only use detergents, which intended to be used in automatic washer-disinfectors. Do not use 
solvents in your machine, as there may be a danger of explosion.

Take care when handling liquids such as detergents, rinsing or neutralising agents. These may 
contain acids or alkalis. Follow the instructions and safety procedures on the packaging carefully 
and wear protective gloves and goggles. Read the Material Safety Data Sheets.

Do not allow any acids or solvents, especially hydrochloric acid and chlorides, into the wash 
chamber.

Be careful when sorting instruments with sharp pointed ends. If possible, place the pointed end 
downwards.

Install special inserts in accordance with the instructions provided.

When using the machine be careful not to scald or burn yourself, especially by opening the door.
Baskets and inserts must first be allowed to cool down. Any water, which may have collected in 
incorrectly loaded items, will be very hot and should be emptied into the wash chamber.

Do not touch the inner surfaces of the wash chamber or the heating elements after the end of a 
program. You could burn yourself.

Do not hose the machine down to clean it.

Do not sit or lean on the open door. This could cause the machine to tip and be damaged.

When disposing of an old machine, make sure the door catch is removed. This will prevent 
children at play from being accidentally locked in.

Be careful when removing the panels and working inside the machine because of possible burrs 
and sharp edges. If possible, use safety gloves.

The manufacturer cannot be held responsible for damage caused by failure to heed the warning 
and safety instructions.

USED SAFETY SYMBOLS

Dangerous voltage

2

INTENDED USE OF THE MACHINE

The Deko 190 Washer Disinfector is suitable for automatic cleaning and thermal disinfection of 
human waste containers intended for re-use such as;

* portable sanitary pans;
* supports for single-use bedpans;
* hospital bowls;
* urine bottles; 
* suction bottles and
* products similar to the above and used for similar purposes

 5

Summary of Contents for DEKO 190GT





































Reviews:

Related manuals for DEKO 190GT