background image

12  

 

 

 
 

Rhino Ironworks® PSIW2418 

Limited Warranty 

1. 

Rhino Metals, Inc. (the “Company”) warrants to the original consumer (the 

”Purchaser”) that the Ironworks PSIW2418 safe (the “Safe”) will be free from 
defects in workmanship and  materials for a period of one (1) year from the date 
of purchase. These warranties are not assignable or transferable to any other 
person.  

2. 

The Company is not responsible for lost or forgotten combinations. 

3. 

Any damage to the Safe as a result of destruction, misuse, tampering, abuse, 

neglect, accident, improper installation, modification, unauthorized service or 
violation of the instructions furnished by the company will void this warranty. 

4. 

The sole responsibility of the Company shall be limited to the repair or 
replacement (in its sole discretion) of any component of the Safe which fails to 
conform to this warranty at no cost to the Purchaser for a period of one (1) year 
from the date of original purchase. 

5. 

Contact the Company directly to obtain service under this warranty. A Return 
Authorization Number must first be obtained prior to returning defective 
products to the Company. 

6. 

Products shipped without prior Return Authorization and Return Authorization 
Number may not be accepted. The Company will not be responsible for their 
disposition and/or cost of return to the owner. 

7. 

The Company will not assume any responsibility for any loss or damage incurred 
in shipping.  All returned products should include a copy of the original invoice in 
order that this warranty may be honored. 

8. 

This warranty is not an insurance policy.  The Company is not responsible for 
damage or theft of the Purchaser’s Safe or its contents. 

9. 

Any implied warranties which the Purchaser may have are limited to the duration 
of the warranties described above.  There are no further warranties which extend 
or apply beyond the face hereof, and the Company expressly disclaims and 
excludes any and all warranties of merchantability or fitness for a particular 
purpose.  Some states do not allow limitation on how long an implied warranty 
lasts, so the above limitation may not apply to you. 

10.  Repair or replacement shall be the sole remedy for the Purchaser under this 

warranty.  The Company shall not be liable for any direct, indirect, incidental or 
consequential damages, losses or expense arising from the use or misuse of the 
Safe.  Some states do not allow the exclusion or limitation of incidental or 
consequential damages so the limitation may not apply to you.  

11.  This warranty gives you specific legal rights, and you may also have other rights 

which may vary from state to state. 

Rev 15A 

Summary of Contents for PSIW2418













Reviews: