background image

13500lb - 175000lb - 20000lb

© 

Rhino Winch Co

10

© 

Rhino Winch Co

WARNING

MOVING PARTS ENTANGLEMENT HAZARD

• 

Always 

ensure the hook latch is closed correctly.

• 

Never 

apply a load to the hook tip or latch. Apply 

the load only to the center of the hook.

• 

Never 

use a hook if the throat opening has 

increased, or the tip is bent / twisted. 

• 

Always

 use a hook with a latch.

WARNING

CUT AND BURN HAZARD

To avoid injury to hands and fingers: 

• 

Always

 wear leather gloves when handling the 

winch rope.

• 

Always

 be aware of possible hot surfaces such as 

the winch motor, drum or drop during / after use. 

CAUTION

MOVING PARTS ENTANGLEMENT HAZARD

To avoid injury to hands and fingers:

• 

Never

 leave any remote control where it can be 

activated during free spooling, ringing or when 
the winch is not being used.

• 

Never 

leave the wireless winch remote control 

turned on when installing, free spooling, rigging, 
servicing winch or when the winch is not being 
used.

CAUTION

CUT AND BURN HAZARD

• 

Never 

let winch rope slip through your hands.

NOTICE

AVOID WINCH AND EQUIPMENT DAMAGE

• 

Always avoid side pulls that can bunch the rope at one end of the drum.                                                     
This can damage the rope or the winch.

• 

Always ensure the clutch is fully engaged or disengaged.

• 

Always take care not to damage the vehicle frame when winching.

• 

Never fully submerge the winch in water.

• 

Always store the remote controls in a clean, dry area.

Summary of Contents for 13500lb


















Reviews: