Rhino Electronic Security
(a division of Cornick Pty. Ltd.)
ABN:
74 001 621 610
Web
Head Office
:
9 Hannabus Place,
McGraths Hill, NSW 2756
AUSTRALIA
Ph: (+61) 2 4577 4708
Fax: (+61) 2 4577 4885
Haberfield Sales Office
:
223 Ramsay St,
Haberfield, NSW 2045
AUSTRALIA
Ph: (+61) 2 9716 0444
Fax: (+6) 2 9799 2024
Villawood Sales Office
71 Middleton Road
Villawood NSW 2163,
Australia
Ph: ( +61) 2 9743 8222
Fax : (+61) 2 9743 8590
V i d e o S u r v e i l l a n c e
D i g i t a l V i d e o R e c o r d e r s ( D V R )
H o m e a n d B u s i n e s s A l a r m s
C a r A l a r m s
I m m o b i l i s e r s
V e h i c l e T r a c k i n g S y s t e m s
R e c e i v e r / T r a n s m i t t e r S e t s
C e n t r a l L o c k i n g
REMOTE LEARNING INSTRUCTIONS v1.2
Alarm
# Remote
Compatible Remotes
Instructions
GTR
5
GTRTX
Green
LED
Fixed Code
Before entering this mode, make sure you have all remotes present that you wish to utilise with this alarm system, as the alarm
automatically erases all remotes when you enter this mode.
1.
Arm then disarm the alarm system. While the system is disarmed, open and close your drivers door (get inside the
vehicle), making sure the interior light is coming on as you open the door.
2.
Within 30 seconds, turn the car ignition key from the off position to the ignition on position
8 times
.
3.
10 seconds later, the blinkers will flash 8 times to confirm that you have entered the remote learning mode. Repeat
steps 1 & 2 if you do not receive the flashes.
4.
Now press and hold the button 1 on the new remote you wish to learn in. The siren will beep once to confirm the code
has been learnt. Repeat this step for up to 3 remotes. You can use this process to delete lost remote controls by
learning in the same remotes in succession to replace each of the 3 memory locations so that the old remote code/s are
erased.
5.
The system will automatically exit the learning mode 20 seconds after the last press of a remote.
GTS
3
GTSTX
Red
LED
Before entering this mode, make sure you have all remotes present that you wish to utilise with this alarm system, as the alarm
automatically erases all remotes when you enter this mode.
1.
Arm then disarm the alarm system. While the system is disarmed, open and close your drivers door (get inside the
vehicle), making sure the interior light is coming on as you open the door.
2.
Within 30 seconds, turn the car ignition key from the off position to the ignition on position
20 times
.
3.
30 seconds later, the blinkers will flash 3 times to confirm that you have entered the remote learning mode. Repeat
steps 1 & 2 if you do not receive the flashes.
4.
Now press and hold the button on the new remote you wish to learn in. The siren will beep once to confirm the code
has been learnt. Repeat this step for up to 3 remotes. You can use this process to delete lost remote controls by
learning in the same remotes in succession to replace each of the 3 memory locations so that the old remote code/s are
erased.
5.
The system will automatically exit the learning mode 15 seconds after the last press of a remote.
GT
GTTX
Orange
LED
To add a new transmitter to your alarm, simply follow the procedure below:
1.
Turn the vehicle’s ignition on.
2.
Immediately press and hold the Left button on the
Original
remote control until the siren starts to beep
(approximately 4 seconds) and then release the button.
3.
Immediately press and hold the same (Bottom) button on the
New
remote control for at least 4 seconds.
4.
Turn the vehicle’s ignition off.
5.
The new remote control is now programmed into the alarm.
