background image

 

3

 

 

 

 
 
Your Rhino Security system incorporates the latest in high security & convenience features. 
It is possible to customise your security system so that it suits your requirements perfectly. 
Detailed below is the full list of programmable features that can either be turned on or 
turned off.  
We have set at the factory, the most common configuration chosen and these settings are 
listed in the REGISTER Settings listed below. Once the desired features have been selected, 
the selection is permanently retained in memory, even if power is removed.  
 

To turn on or turn off any feature use the following procedure:  
eg

 to disable audible arming. 

 

1.

 Arm then disarm the alarm system.  

2.

 Within 20 seconds of disarming, turn the ignition key to on. 

3.

 Press the remote control button an equal number of times to the selected feature’s   

code

 no. (eg 6 times for auto-rearm). 

Leave a 2 sec. gap 

between

 each press

. The siren 

will chirp to confirm each press. 

4.

 Immediately turn the ignition to off after the last press. 

5.

 The system will then confirm which features are activated via audible readout. If a feature 

is enabled the siren will chirp out its code in beeps from the siren corresponding to the 
number shown in the column 

“Press Remote This Many Times”

. The siren in this example 

will beep in order Once, then 4 Times, then 6 times. The system skips voltage drop (2 beeps), 
and door ajar (3 beeps) as these features are off. Please note that features 9-11 are 
excluded from the confirming number of beeps. Feature 5 is not used. 
 

 

PROGRAMMABLE 

FEATURE 

Press 

Remote 

This 

Many 

Times 

INITIAL 

FACTORY 

SETTING 

 

DESCRIPTION 

Audible Arm/Disarm 

ON 

This feature when turned off, stops the siren 
from beeping for arm & disarm confirmation i.e. 
only the blinkers will flash. 

Voltage Drop 
(Current) Sensing 

 

Off 

If activated, this feature will prevent the alarm 
triggering via sensing a drop in voltage in the 
vehicle’s electrical system. This may be 
necessary where engine thermo fans cut in 
automatically or there are other accessories 
active even when the ignition is turned off eg  
fridges, car phones. 

No Door Ajar Warning 

OFF 

When this feature is on, the door ajar warning 
feature is removed (the siren & indicators will not 
beep & flash for 3 sec. if a door is not closed 
properly). 

Shock Sensor  

ON 

Activate Two Stage Shock Sensor. 

Summary of Contents for GXa










Reviews: