RIB AA50130 Manual Download

Page: 40 / 80

POINT B - SETTINGS

DIP 1

BARRIER SLOWSPEEDS ADJUSTMENT IN OPENING AND CLOSING (ON) (See Point C)

DIP 1-2

STORING/ERASING RADIO CODES FOR MOTOR CONTROL (See Point D)

DIP 1-2-3 STORING/ERASING STORING/ERASING for relay R-AUX command (point E)
DIP SWITCHES CONTROL
DIP 4

Single impulse command START and RADIO - step-by-step (ON) - automatic (OFF)

DIP 5

Enable radio system SUN (ON) - SUN-PRO (OFF)

DIP 6

NORMAL operation (OFF) - PARK operation (ON)

DIP 7

ON - photocells self-test ENABLED

DIP 8

OPEN 2 command operation in PARK mode

ON - OPEN 2 command is always enabled

OFF - OPEN 2 command works if there is no vehicle on the magnetic sensor connected

to the TLC input (Traffic light control contact opened).

DIP 9

Courtesy light management (OFF)

They work with 1 Relay card ACQ9080 or 3 Relay card ACQ9081 (If none of the optional cards is
connected, turn DIP9 to OFF).

DIP 10

Operation after black-out

ON - the boom arm automatically closes if not already closed.

OFF - the boom arm remains still on the point it was when blackout occurred

DIP 11

ON - 3-phase motor

OFF - 1-phase motor

DIP 12

OFF - Electromechanical limit switches welded on pc card

DIP 13

ON - Lamp with flashing light / OFF - Blinker operation with fixed power supply

TIPO MOTORE

DIP 14

DIP 15

DIP 16

RAPID S 3 m

OFF

RAPID S 4 m

OFF

LED WARNINGS

DL1

PROG programming activated

(red)

DL2

Barrier opening

(green)

DL3

Barrier closing

(red)

DL4

Opening limit switch LSO

(green)

DL5

Closing limit switch LSC

(red)

DL6

STOP command (NC)

(red)

DL7

PHOTO 1 contact (NC)

(red)

DL8

PHOTO 2 contact (NC)

(red)

DL9

EDGE 1 contact (NC)

(red)

DL10

PROG and RADIO (on MOLEX connector) commands

(green)

DL11

TCA - automatic closure time enabled

(red)

DL12

Remotes programming enabled

(red/green)

DL13

P1 managed by APP

(blue)

OPEN 1

OPEN 1 command (to enter)

(green)

OPEN 2

OPEN 2 command (to exit)

(green)

CLOSE command (NO)

(green)

START

Single impulse command (NO)

(green)

B.I.O

Clock command (NO)

(green)

OK CLOSE Confirmation of closing command

(green)

TLC

Magnetic sensor control for traffic light control

(green)

PROBE

Engine room temperature sensor for heating the engine in particularly cold climates, up to -30
° C (connection to connector J3) code ACG4666.

ADJUSTMENTS

TRIMMER LOW SPEED OPEN and TRIMMER LOW SPEED CLOSE - Slow speed regulators in opening
and closing approach

Slow speed regulation is performed by acting on the LOW SPEED OPEN and LOW SPEED CLOSE
trimmers through which the output voltage across the motor is varied (turning it clockwise
increases the speed).
The deceleration is automatically determined by the limit switches at about 30° before
reaching the opening or closing limit switch.

TRIMMER TCA - Automatic closing time regulator
standard not enabled and LED DL11 OFF
(trimmer rotated completely counter-clockwise)

With this trimmer it is possible to adjust the waiting time before having automatic closing.
The automatic closing is obtained only with the barrier open as a result of the command given
by the opening commands and led DL11 ON (trimmer rotated clockwise to enable the feature).
The pause time can be adjusted from a minimum of 2 s to a maximum of 2 minutes.

R-AUX - AUXILIARY RELAY CONTACT (NO)

By default this relay is set as courtesy light (max 700 W - 3 A- 230 Vac) to operate 3 minutes at
each command, with time renewal at each command.
It is possible to activate the R-AUX contact by remote control by performing the memorization
procedure described in point E.

POINT C - BARRIER SLOWSPEEDS ADJUSTMENT IN OPENING AND CLOSING

This check is meant to facilitate the installer during the start-up of the system or for any other
future controls:
1 -

Turn DIP 1 to ON

, the red led DL1 starts blinking

2 -

Press the PROG button

and hold it (movement is now performed in “hold-to-run” mode,

open-stop-close-stop-open etc.). If the GREEN led DL2 is on, the boom arm opens. If the RED
led DL4 is on, the boom arm closes.

3 -

Carry out the slow-down speed calibration => Turn the LOW SPEED OPEN and LOW SPEED
CLOSE trimmer to minimum =>

Press the PROG button

and hold it => After 1 s of movement

the low speed will be enabled.

CAUTION: Check that the motor has enough force to move the boom both in opening and

closing. If not, increase the value set on the trimmers until the optimal operating
condition is reached.

CAUTION: In areas subject to particularly cold temperatures, turn the trimmers clockwise 5°

more than the normal value, or apply the optional probe (code ACG4666) to heat
the engine.

4 -

Turn DIP1 to OFF

=> the red LED DL1 turns OFF.

During Point C procedure the safety-strip and photocells are not enabled.

POINT D - PROGRAMMING RADIO CODES FOR OPENING (1000 CODES MAX) - with radio module

ACG8069

ATTENTION: before storing the radio codes, use DIP 5 to select which transmitters to use:
DIP 5 OFF

: SUN-PRO variable code transmitters can be memorized:

SUN-PRO 2CH 2-channel - red keys and white led

cod. ACG6210

SUN-PRO 4CH 4-channel - red keys and white led

cod. ACG6214

DIP 5 ON (default)

: You can store transmitters with fixed code SUN:

SUN 2CH 2-channel - blue keys and white led

cod. ACG6052

SUN 4CH 4-channel - blue keys and white led

cod. ACG6054

SUN CLONE 2CH 2-channel - blue keys and yellow led

cod. ACG6056

SUN CLONE 4CH 4-channel - blue keys and yellow led

cod. ACG6058

ATTENTION: it is not possible to memorize at the same time transmitters with fixed code and

transmitters with variable code.

Programming can be done only when the gate is stationary.
1 - First set

DIP 1 to ON

and then

DIP 2 to ON

. The LED DL12 flashes red for 10 s.

2 - Press the TRANSMITTER button (usually channel A) within the allotted 10 s. If the remote

is memorized properly LED DL12 blinks green and a buzzer tone confirms the correct
memorization. The 10 s for programming the codes are automatically renewed, with LED
DL12 which flashes red, in order to store the next transmitter.

3 - To finish programming, wait 10 s, or press the PROG button briefly. LED DL12 stops flashing.
4 - Re-set

DIP 1 to OFF

and

DIP 2 to OFF

ALL RADIO CODES FOR TOTAL OPENING CANCELLATION PROCEDURE

Cancellations can only be performed when gate is stationary.
1 - Set

DIP 1 to ON

and then

DIP 2 to ON

2 - LED DL12 flashes red for 10 s.
3 - Press and hold the PROG button for 5 s. Memory cancellation is indicated by two green

flashes of LED DL12 and 2 tones of the buzzer.

4 - LED DL12 flashes red again for 10 s and you can add new codes as shown above.
5 - Re-set

DIP 1 to OFF

and

DIP 2 to OFF

RADIO CODES MEMORY FULL INDICATOR (FOR TOTAL OPENING)

Indication is visible only when gate is stationary.
1 - Set

DIP 1 to ON

and then

DIP 2 to ON

2 - The LED DL12 flashes green 6 times when the memory is full (1000 codes). Now LED DL12

blinks red for 10 s enabling possible cancellation of all codes.

3 - Re-set

DIP 1 to OFF

and

DIP 2 to OFF

POINT E - PROGRAMMING RADIO CODES (FOR R-AUX RELAY) (1000 CODES MAX) - with radio

module ACG8069

* Remote control management can be enabled only by the RIB GATE app.
R-AUX normally works as a courtesy light for 3 minutes.
Through the RIB GATE app it is possible to configure the operation of this relay as desired.

Programming can be done only when the gate is stationary.
1 - Set

DIP 1 to ON

DIP 2 to ON

and then

DIP 3 to ON

. DL12 flashes orange for 10 s.