18
F
DEFAUT
SOLUTION
Après avoir effectué les différents raccordements et avoir allumé le courant, toutes les leds
sont éteintes.
Vérifier l’intégrité des fusibles F, F1 et F2.
En cas de fusible en panne en utiliser uniquement de valeur adéquate.
F 1,6A FUSIBLE de PROTECTION TRANSFORMATEUR (extérieur à la fiche PARK 24V)
F1 = 2A F2 =10A
Le moteur ouvre et ferme, mais n’a pas de force et se déplace lentement.
Vérifier le réglage des ressorts d’équilibrage.
Vérifier le réglage trimmer LOW-SPEED.
La barre effectue l’ouverture, mais ne se referme pas après le temps configuré.
S’assurer d’avoir activé le DIP 3 sur ON.
Le bouton OUVRIR 1 toujours inséré.
Remplacer le bouton ou interrupteur du sélecteur.
La phase de ralentissement ne s’exécute pas
Vérifier le réglage des ressorts d’équilibrage.
Vérifier le réglage trimmer LOW-SPEED.
OPTIONS -
Pour les branchements et les données techniques des accessoires, se conformer aux livrets d’instruction correspondants.
FONCTIONS SUPPLEMENTAIRES AVEC CARTE EXPANDER 24V (code ACG5471)
D5
D4
D3
D2
!! BRANCHER LA FICHE EXPANDER 24V EN ABSENCE DE COURANT !!
LEGENDE
TR => Trimmer de réglage temps éclairage de zone
1-2 => Alimentation 24Vdc pour photocellules, “fotocoste”, etc….
3-4
=> Contact feux
SORTIE 1
5-6
=> Contact feux
SORTIE 2
7-8 => Contact éclairage de zone
9
=> Contact
OUVERTURE 2
(NO)
10 => Contact IN PARK (NO)
11 => Commande OK CLOSE (NO)
12 => Commun
SIGNALISATIONS LED CARTE EXPANDER 24V
D2 signalisation contact commande OUVERTURE 2
D3 signalisation contact IN PARK
D4 signalisation contact OK CLOSE
D5 Présence tension
N.B.: Pour un fonctionnement correct, le LED D5 doit toujours être allumé.
ATTENTION: LA PLATINE PARK PAR L’INTERMEDIAIRE DU DIP 6 HABILITE OU NON
CERTAINES COMMANDES DE LA FICHE EXPANDER, IL FAUT DONC ETRE
ATTENTIF A:
SI DIP 6 OFF, FONCTION NORMALE
LES COMMANDES OUVERTURE 2, OK CLOSE ET IN PARK NE SONT PAS ACTIVES ALORS
QUE LA GESTION DES FEUX ET LA LUMIERE DE SERVICE SONT DISPONIBLES.
GESTION FEUX EN FONCTIONNEMENT NORMAL AVEC EXPANDER
-
SCHEMA B -
SORTIE 1 (NO)
SORTIE 2 (NO)
ROUGE IN
VERT IN
PRESIDENT FERME
ETEINT
ETEINT
PRESIDENT OUVRE AVEC OUVER. 1
ALLUME
ETEINT
PRESIDENT OUVERT
ETEINT
ALLUME
PRESIDENT EN FERMETURE
ALLUME
ETEINT
- SCHEDA D -
SORTIE1
(NC)
SORTIE1
(NO)
SORTIE2
(NC)
SORTIE 2
(NO)
ROUGE
IN
VERT
IN
ROUGE
OUT
VERT
OUT
PRESIDENT FERME
ALLUME
ETEINT
ALLUME
ETEINT
PRES. OUVRE AV/OUVER.1
ALLUME
ETEINT
ALLUME
ETEINT
PRESIDENT OUVERT
ETEINT
ALLUME
ALLUME
ETEINT
PRES. EN FERMETURE
ALLUME
ETEINT
ALLUME
ETEINT
PRESIDENT FERME
ALLUME
ETEINT
ALLUME
ETEINT
PRES. OUVRE AV/OUVER.2
ALLUME
ETEINT
ALLUME
ETEINT
PRESIDENT OUVERT
ALLUME
ETEINT
ETEINT
ALLUME
PRES. EN FERMETURE
ALLUME
ETEINT
ALLUME
ETEINT
MODE DE FONCTIONNEMENT PARK DIP 6 ON AVEC CARTE EXPANDER
VOIR SCHEMA D
POUR ENTRER:
A condition qu’une voiture soit présente sur le détecteur magnétique, l’ouverture de la
barrière peut être commandée par l’intermédiaire du bouton OUVERTURE 1, pas-à-pas ou
par commande radio. La barrière reste ouverte jusqu’à ce que la voiture soit passée devant
les photocellules situées en correspondance avec la ligne de fin de passage. La fermeture
est exécutée une seconde après la fin du passage (photocellule libre), et est protégée par
des photocellules. Celles-ci commandent l’inversion en ouverture de la barrière même si la
voiture reste dans le rayon d’action des sécurités.
POUR SORTIR:
L’ouverture de la barrière est consentie par l’intermédiaire du bouton OUVERTURE 2 branché
à un détecteur magnétique ou à un autre dispositif, à condition qu’il n’y ait pas de moyen
de transport sur le détecteur magnétique d’entrée (voir DIP 8 pour exclusion du blocage de
priorité). La barrière reste ouverte tant que la voiture n’est pas passée devant le photocellules
situées en correspondance avec la ligne de fin de passage.
La fermeture est exécutée une seconde après la fin du passage (photocellule libre) et est
Summary of Contents for PRESIDENT
Page 45: ...45 NOTES ...