RIB PRESIDENT, Manual

25

the battery. The functioning of the bar is ensured up to a voltage level of 
about 20V, after which we have a signalling given by the recharge card 
of the gearcase which blocks the bar and makes the battery state pilot 
light lighten. Once the network voltage is back, the recharge card starts 
charging the battery and the battery state led switches off. It is sufficient to 
press the remote control (or the opening button 1 or 2 or the step by step 
button ) to open the bar. When the bar is open, give a closing command 
or wait the pause time before the automatic closing => the bar starts 
closing. When closed, the normal functions are reactivated. 

DIP 9 - ON =>   

with lack of network voltage the bar opens automatically, the battery state 
led switches on and all controls are inhibited. When the network voltage is 
back, the bar closes immediately thus resetting the controls and safeties 
functioning. 

IN CASE NO BATTERY IS CONNECTED

, through the DIP 10 you can have the following 

options:

DIP 10 - OFF => 

 In lack of the network voltage the bar stays still or, in case it is moving, it 
stops. Once the network voltage is back, it is sufficient to press the remote 
control, 1 and 2 OPENING buttons or step by step button to open the bar. 
When the bar is open, give a closing command or wait the pause time 
before the automatic closing => The bar starts closing => When closed, 
the normal functions are reactivated. During the realignment the securities 
are active.

DIP 10 - ON => 

 At the return of the network voltage the bar closes if open, and doesn’t 
close only in case the clock function is active. (see OPENING 1 button).

SAFETY FITTINGS OPERATION

SECURITY LOCK 

For a correct functioning of the system, the DL4 led must always be on to signal that the 
manual release has not been activated. If the DL4 led is off no movement of the bar is allowed 
because it has been manually released with the special key. 

ENCODER

It has the duty to act as security and to define the running, both during the closing and the 
opening phase, with reversal of the movement.
It is possible to exclude the ENCODER, which only functions as security, through DIP 7 (OFF). 
In case the ENCODER should not work (not fed, disconnected wires or faulty) the movement 
of the bar is not carried out. 
If after a first intervention of the ENCODER in closing or opening phase there is a second one, 
obviously in the contrary sense, the bar stops and then reverses for 1 sec. The bell (buzzer 
optional) will be activated to signal the alarm state for 5 minutes and the flashlight will be 
active for a minute. 
During or after the 5 minutes of sounding alarm (buzzer optional), it is possible to reset the 
functioning of the bar by pressing any control button. 

PHOTOELECTRIC CELL  (terminals 3-4)

When the bar is down, if there is an obstacle in the radium of the photoelectric cells and 
the opening command is given, the bar opens (during the opening phase the photoelectric 
cells will not work).
The photoelectric cells will only work during the closing phase (with reset of the reverse 
motion after a second even if they are busy). 

N.B.:  Every six months make sure to check that photocells are not out of order.
ATTENTION: In case the receiver led remains lit, 
malfunctioning of the main supply is suspected. 
It is advisable to connect electrically the photocells stands 
to the contact 10, to shield the photocells from external 
noise.
Be careful not to short circuit the system when the supply 
phases are inverted!

STOP BUTTON (terminals 3-5)

During whatever operation the STOP button stops the bar. 
If pressed when the bar is completely open the automatic closing is temporarily excluded (if 
selected through DIP3). It is thus necessary to give a new command to make it close again.
At the following cycle the automatic closing function is reactivated (if selected through DIP3).

FLASHLIGHT (terminals 9 positive / 13 negative)
N.B.:  This electronic board can feed ONLY FLASHLIGHTS WITH LIGHTENING CIRCUIT 

and a 24V lamp. 

The flashlight is active during the motion of the bar, or to signal the impact alarm state for 

1 minute. 
Use a flashlight (code ACG7061) with a max. 24V 20W lamp.

BUZZER (Optional - terminals 3 positive / 12 negative)

During the opening and the closing phase the buzzer will give a sounding intermittent signal.
In case of intervention of the securities (alarm) this sounding signal increases the frequency 
of the intermittence. 
Power provided for the functioning of the 200mA buzzer at 12Vdc.

TECHNICAL CHARACTERISTICS

- Humidity  

 < 95% without condensation

- Feeding tension 

230V~ ±10%

- Frequency  

50/60 Hz

- Battery feeding   

20-24,5Vdc

- Transformer power 

 130VA - V primary 230 Vac - V 
Secondary 18Vac

- Standby modus 

100mA

- Network micro interruptions   

100ms

- Flashlight max. load  

24Vdc 20W

- Power available for  per photoelectric cells and fixtures
 

1A ±15% 

- Power available on radio connector  

200mA  

-  All the inputs must be used as clear contacts because the power supply is generated inside 

(safe power) the control panel, and it has been laid down in such a way to guarantee a 
double or strengthened insulation  in relation to the parts with dangerous power. 

-  Eventual external circuits connected to the outputs of the control board or of the expander 

card must be carried out making sure that a double or strengthened insulation is used in 
relation to parts with dangerous power.

-  All inputs are run by a programmed integrated circuit which does a self check every time 

it starts operating.

TROUBLE SHOOTING

After having carried out all connections, by carefully following the layout and having 
positioned the bar in intermediate position, check the correct ignition of LEDS DL2, DL3, DL4; 
the led DL1 can be ignited or extinguished.
In case of no ignition of the LEDS, always with bar in intermediate position, check the 
following and replace any faulty components.
DL1 

switched off 

Faulty Encoder 

DL2 

switched off 

Faulty Stop button

DL3 

switched off 

Faulty photocells

DL4 

switched off 

Faulty manual release or unblocked bar.

During functioning with personnel present, with DIP 1 at ON, check that during opening the 
green DL6 LED switches on and that during closing the red DL7 LED switches on. If not, 
invert the wires of the motor.

24Vdc

Cont.

10

G

B