Richmond GTR500, User Manual

13

14

LED1
LED2
LED3

ON

OFF

PART B: Control System User Manual

1

5

Gate-moving Logic

(A) In gate-opening phase:  The gates stop if the transmitter/push button/key selector is activated, and close when

the transmitter/push button/key selector is reactivated.

(B) In gate-closing phase:  The gates stop if the transmitter/push button/key selector is activated, and open when

the transmitter/push button/key selector is reactivated.

(C) In gate-opening or gate-closing phase:  For safety purpose, the gates stop if encountering obstacles.

Checking the Gate Movement

1). Release the gear with the release key and move the gate to the middle so that it can move in both

 the gates reaches the limit   

     opening and closing directions; then lock the gear.

2). Operate the gate to opened and closed position several times, and make sure

     switch at least 2~3 centimeters before the mechanical stop.

LED Indicat

ion

LLED2

ED2 D Key/S Ke

y

Key selector, or the push button is activated, LED2 will be on.

LLED4

ED4

LED4

 Ph

1

 will be on when Ph1 are triggered.

LLED3

ED3

LED3

 Ph

2

 will be on when Ph2 are triggered.

Antenna

Lit+

Lit- Lat+ Lat- M1+ M1- M2+ M2-

Lmt3 Lmt4

Lmt2

SKey

Ph1 PhVcc

Ph2 PhVcc

5V

S1

S2

ANT

GND

GND DKey

GND

GND

GND Lmt1

GND

J5

RF1

K3

K2

K1

J4

J3

J7

J8

CO

NC

NO

CO

-

+

-

+

CO

NO

NC

-

+

CO

NO

NC

NC

NO

CO

-

+

11111111  

  1

2

19

19

19

19

19

19

19 

19    

LED2

LED4 LED3

Function Of The LED Display

LED Display         Programmable Functions

LED Display         Programmable Functions

When the gate is opening, the LED Display 

show ‘OPN’ for 2s and then change to Amp 

current indication 

When the gate is stopped, the LED Display show 

‘STP’ until next commend has been made, after 

10s no further movement, the LED turns to OFF

When the gate is closing, the LED Display show 

‘CLS’ for 2s and then change to Amp current 

indication 

LED display shows “S01” means the panel did not 

detected the M1+/M1 and M2+/M2 both been 

connected before the system learning procedure, 

check for motor wire connection, for dual gate 

system

The memory of the system is all deleted/cleaned 

by press and hold the UP + SET+ DOWN button 

together for 5s and the panel will be back to 

default settings

LED display shows “S02” means the panel did not 

detected the M1+/M1 but detected M2+/M2 been 

connected, notice the installer to check the motor 

wire connection, if this is single gate system, 

motor wire should connect to M1+/M1 not on 

M2+/M2

LED display show “S03” means same button on 

the remote has been identified for more than 2 

functions

[LEA] means motor into the system learning 

mode, do not interrupt during this procedure.

[D-G] means motor completed the learning 

procedure for dual gate installation

.

[S-G] means motor completed the learning 

procedure for single gate installation

.

[N-L] means system learning failed.

4

3

5

6

7

8

9

10

11

12

13

14

15

16

17

18

20

2

1

2

2

2

3

2

4

2

5

2

6