Ricoh Aficio IS 2425 Operating Instructions Manual Download

Page: 208 / 288

Registering Addresses and Users for Facsimile/Scanner Functions

200

Fax Destination

This section describes how to register, change, and delete a fax destination.

Registering a Fax Destination

This section describes how to register a fax number.

Press

[

System Settings

]

Press

[

Administrator Tools

]

Press

[

Next

]

Press

[

Address Book Management

]

Check that

[

Program / Change

]

is selected.

Select the name whose fax destination you want to register. Press the name
key, or enter the registered number using the number keys.

If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.

Press

[

Fax Dest.

]

Enter the fax number using the number keys, and then press

[

]

under

Facsimile No..

Specify optional settings such as “SUB Code”, “SEP Code”, and “Interna-
tional TX mode”.

Summary of Contents for Aficio IS 2425

































































































































































































































































































Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands

Ricoh Aficio IS 2425, Operating Instructions Manual

Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands