Ricoh Aficio IS 2425 Operating Instructions Manual Download

Page: 214 / 288

Registering Addresses and Users for Facsimile/Scanner Functions

206

IP-Fax Destination

This section describes how to register, change, and delete a IP-Fax destination.

Note

❒

For details about sending an IP-Fax, "Sending by IP-Fax", Facsimile Reference.

Reference

"Sending by IP-Fax", Facsimile Reference

Registering an IP-Fax Destination

This section describes how to register an IP-Fax Destination.

Press

[

System Settings

]

Press

[

Administrator Tools

]

Press

[

Next

]

Press

[

Address Book Management

]

Check that

[

Program / Change

]

is selected.

Select the name whose IP-Fax destination you want to register.

Press the name key, or enter the registered number using the number keys.
If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.

Press

[

Fax Dest.

]

Press

[

IP-Fax

]

Press

[

Change

]

under ”IP-Fax Destination".

Enter the IP-Fax destination.

Press

[

]

Summary of Contents for Aficio IS 2425

































































































































































































































































































Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands

Ricoh Aficio IS 2425, Operating Instructions Manual

Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands