Ricoh Aficio MP 1600 Facsimile Reference Manual Download

Page: 151 / 204

Printing a File from Memory

141

Printing a File from Memory

If you want to check the contents of a file that is stored in memory and not yet
sent, use this procedure to print it out.

Press the

{

Job Information

}

key.

Select

[

Print TX Standby File

]

using

{U}

{T}

, and then press the

{

}

key.

Select the file you want to print using

{U}

{T}

To cancel printing, press the

{

Escape

}

key. The display returns to that of step

Press

[

Print

]

To cancel printing after pressing

[

Print

]

, press the

{

Clear/Stop

}

key. The display

returns to that of step

The display returns to that of step

after printing a TX Standby File.

Repeat from step

, if you want to print another file.

Press the

{

Escape

}

key.

The standby display appears.

ARX037S

Summary of Contents for Aficio MP 1600













































































































































































































Search results

Summary of Contents for Aficio MP 1600

Reviews:

Related manuals for Aficio MP 1600

Brands by name

Popular brands

Ricoh Aficio MP 1600, Facsimile Reference Manual

Search results

Summary of Contents for Aficio MP 1600

Reviews:

Related manuals for Aficio MP 1600

Brands by name

Popular brands