Ricoh Aficio MP 1600 Facsimile Reference Manual Download | Manualshive

Page: 39 / 204

background image

Internet Fax Functions

29

1

Note

❒

The Internet Fax function supported by this machine is compliant with ITU-
T Recommendation T.37.

❒

You can receive e-mail messages with an attached TIFF-F image from computers.

❒

Though Internet Fax documents are normally sent via an SMTP server, you
can also send Internet Fax documents directly to their destinations without
going through an SMTP server. To do this, program “Use SMTP Server” to a
User Function key in advance.

❒

When sending Internet Fax documents, you can specify “Attach Subject” and
“Return Receipt” in

[

TX Mode

]

.

❒

You can limit the size of transmitted e-mail messages in “E-mail Settings” of
“Fax Features”.

❒

See “Received Images” for how e-mail is actually received by the computer.

❒

For details about how to confirm the transmission result, see “Checking the
Transmission Result (TX File Status)”.

❒

When you transmit an Internet Fax specifying a user code, and the email ad-
dress is set as the routing destination of the specified user code, a Communi-
cation Result Report is sent after the transmission is completed. This makes it
possible to verify the result of a transmission.

❒

You cannot send e-mails to a destination as cc.

Reference

p.56 “Bypassing the SMTP server”
p.98 “Entering the Subject”
p.99 “Requesting a Reception Notice”
p.125 “Received Images”
p.143 “Checking the Transmission Result (TX File Status)”
“Connecting the Machine”, General Settings Guide
“System Settings”, General Settings Guide
“Fax Features”, General Settings Guide

«
...
37
38
39
40
41
...
»

Summary of Contents for Aficio MP 1600













































































































































































































Reviews:

No comments

Related manuals for Aficio MP 1600

Brand: Oki Pages: 2

Brand: Oki Pages: 52

Brand: Oki Pages: 117

Brand: Oki Pages: 45

Brand: Oki Pages: 112

Brand: Oki Pages: 115

Brand: Oki Pages: 2

PIXMA MX882 Series

Brand: Canon Pages: 34

Brand: Canon Pages: 4

Brand: Canon Pages: 913

Laser Class 700 Series

Brand: Canon Pages: 30

Laser Class 700 Series

Brand: Canon Pages: 6

Laser Class 700 Series

Brand: Canon Pages: 6

Laser Class 700 Series

Brand: Canon Pages: 108

PIXMA MX860 series

Brand: Canon Pages: 9

imagePROGRAF iPF9400

Brand: Canon Pages: 8

PIXMA MX860 series

Brand: Canon Pages: 93

Brand: Canon Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands