Ricoh Aficio MP 1600 Facsimile Reference Manual Download | Manualshive

Page: 42 / 204

background image

Transmission

32

1

T.37 Full Mode

This machine is T.37 full mode compatible. T.37 full mode is an international
standard for Internet Fax transmission. (ITU-T Recommendation, RFC2532)
When an Internet Fax communication is made between T.37 full mode compat-
ible machines, the receiver side sends the return receipt (dispatched) in response
to the reception notice request attached to the sent e-mail. This return receipt in-
cludes the receiver's reception capability information (compression type, paper
size, and resolution). When the receiver is programmed in the Address Book as
the full mode destination, the sender side automatically registers the received in-
formation in the Address Book. This allows you to send a subsequent Internet
Fax document to that receiver based on this information.

❖

Returning a Return Receipt

When e-mail is received, if the sender requests reception notice, the receiver
sends a return receipt that includes the receiving machine's capability (com-
pression type, paper size, and resolution).

❖

Registering the Received Reception Confirmation Contents

When the sender receives the return receipt that includes the receiver's recep-
tion capability, the sender checks that the final recipient address sent is pro-
grammed in the Address Book. If it is programmed as a full mode destination,
the sender automatically registers the receiver's reception capability. The reg-
istered reception capability is updated each time the sender receives new re-
ception capability information. The sender can send documents to the
receiver based on this information.
If the receiver is programmed as the simple mode machine or not pro-
grammed in the Address Book, the receiver's reception capability cannot be
registered.
If you know the receiver's reception capability, you can set it manually.

❖

Requesting a Reception Notice

When the receiver's machine supports T.37 full mode and is programmed as
a full mode machine in the Address Book, the machine requests the reception
notice from the receiver. Then, the machine will receive the return receipt
(sent) that includes the receiver's reception capability.

Note

❒

Use Web Image Monitor to manually program a receiver's reception capabil-
ity information.

❒

If you use Internet Fax transmission, you can send documents to multiple
destinations at once. However, if you specify full mode destinations, since
each destination may have a different reception capability, transmission is
done one by one in the specified transmission order.

Reference

p.99 “Requesting a Reception Notice”
p.178 “Programming Destination Information from Web Browser”

«
...
40
41
42
43
44
...
»

Summary of Contents for Aficio MP 1600













































































































































































































Reviews:

No comments

Related manuals for Aficio MP 1600

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 341

Brand: Samsung Pages: 8

CLX2160N - Color Laser - All-in-One

Brand: Samsung Pages: 118

CLX 3160FN - Color Laser - All-in-One

Brand: Samsung Pages: 142

CLP-770ND - Color Laser Printer

Brand: Samsung Pages: 2

CLP 610ND - Color Laser Printer

Brand: Samsung Pages: 114

Brand: Samsung Pages: 6

Brand: Samsung Pages: 15

CLP 600N - Color Laser Printer

Brand: Samsung Pages: 227

CLP 600N - Color Laser Printer

Brand: Samsung Pages: 118

CLP 300N - Network-ready Color Laser Printer

Brand: Samsung Pages: 94

CJX-2000FW Series

Brand: Samsung Pages: 2

4116 - SCX B/W Laser

Brand: Samsung Pages: 205

3561ND - B/W Laser Printer

Brand: Samsung Pages: 252

3561ND - B/W Laser Printer

Brand: Samsung Pages: 127

Brand: Samsung Pages: 314

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands