manualshive.com logo in svg

Ricoh Aficio MP 1600, Facsimile Reference Manual

The Ricoh Aficio MP 1600 is a versatile multifunction printer capable of high-quality printing, copying, and scanning. With its reliable performance and advanced features, it is a valuable addition to any office. Need assistance? Download the free Scanner Reference manual from 88.208.23.73:8080 to unlock its full potential.

Share
Download
background image

Specifying a Destination

53

1

Note

❒

To send to a G3 fax via a gateway connected to a public telephone line, you
must specify it's the receiver's machine telephone number. For example, if the
receiver's fax number is “0312345678”, specify “5678”. To send from an IP-Fax
to G3 fax without using gatekeeper or SIP server, you must register the gate-
way also.

❒

When you specify a destination with IP-Fax, depending on the receiver's net-
work configuration, you may need to specify the IPv4 address and port num-
ber of the receiving machine. For example, if the receiver's IPv4 address is
“192.168.1.10” and the port number is “2100”, specify “192.168.1.10:2100”.
Ask the network administrator for details.

❒

When you specify a host name, depending on the receiver's network config-
uration, you may need to specify the host name and port number of the re-
ceiving machine. For example, if the receiver's host name is “IPFAX1”and the
port number is “2100”, specify “IPFAX1:2100”. Ask the network administra-
tor for details.

❒

An alias telephone number is a number that is registered in the gatekeeper,
and is available only in the network to which the gatekeeper is connected.

❒

Pay attention to the number of telephone number digits set in the gate-
way/IPv4 address conversion table to avoid transmission error.

Sending to an E-mail Address

This section explains how to specify an e-mail address as a destination.
When using Internet Fax transmission, specify the e-mail address in place of the
fax number.

Important

❒

To use Internet Fax functions, the optional printer/scanner unit must be installed.

❒

In the destination list, register senders, specify their e-mail addresses, and
register as 

[

Sender Only

]

 or 

[

Dest. & Sender

]

 in advance using “Address Book

Management” in “System Settings”.

❒

Internet Fax is executed in only Memory Transmission that starts transmis-
sion automatically after storing documents in memory. If you specify Imme-
diate Transmission in Internet Fax, the “

Try again after switching to

memory transmission.

” message appears. When this happens, press 

[

Exit

]

,

and then switch to Memory Transmission.

A

Press 

[

]

 to switch the destination to e-mail address.

Summary of Contents for Aficio MP 1600













































































































































































































Reviews:

No comments

Related manuals for Aficio MP 1600

Tally T6090 Maintenace Manual preview
T6090
Brand: Tally Pages: 202
Oki MB451wMFP Wireless Setup Manual preview
MB451wMFP
Brand: Oki Pages: 4
Oki MB441MFP Safety Information Manual preview
MB441MFP
Brand: Oki Pages: 40
Oki MC573 Advanced Manual preview
MC573
Brand: Oki Pages: 507
Oki MB441MFP User Manual preview
MB441MFP
Brand: Oki Pages: 176
Samsung SL-M3870FW User Manual preview
SL-M3870FW
Brand: Samsung Pages: 351
YAEN POS58C1 User Manual preview
POS58C1
Brand: YAEN Pages: 4
A&D AD-8120 Instruction Manual preview
AD-8120
Brand: A&D Pages: 32
Ricoh Pro L5130e Settings Manual preview
Pro L5130e
Brand: Ricoh Pages: 44
Xerox WorkCentre 3615DN Brochure & Specs preview
WorkCentre 3615DN
Brand: Xerox Pages: 4
Sharp MX-6500N Media Manual preview
MX-6500N
Brand: Sharp Pages: 38
Bang & Olufsen BEOLINE Quick Start Manual preview
BEOLINE
Brand: Bang & Olufsen Pages: 4
Epson WorkForce Pro WF-C8190DTWC User Manual preview
WorkForce Pro WF-C8190DTWC
Brand: Epson Pages: 162
Epson WorkForce Pro WP-4095 DN Specification preview
WorkForce Pro WP-4095 DN
Brand: Epson Pages: 2
Epson WorkForce Pro WP-4532 Start Here preview
WorkForce Pro WP-4532
Brand: Epson Pages: 4
Epson WorkForce Pro WP-4530 User Manual preview
WorkForce Pro WP-4530
Brand: Epson Pages: 287
Epson WorkForce Pro WP-4520 User Manual preview
WorkForce Pro WP-4520
Brand: Epson Pages: 295
Epson WorkForce Pro WF-C579R User Manual preview
WorkForce Pro WF-C579R
Brand: Epson Pages: 437

Brands by name

Popular brands

Load more brands