background image

Transmission

46

1

Specifying a Destination

This section explains how to specify a destination.
Fax numbers, IP-Fax destinations, and e-mail addresses can be specified.

Note

The display shows the percentage of free memory space for storing originals.
Since fax numbers, IP-Fax destinations and e-mail addresses are programmed
in separate memory, dialing fax numbers using the number keys does not
change the percentage on the display.

Sending Over a Fax Line

Enter numbers directly using the number keys on the right side of the control
panel.

A

Press 

[

]

 to display  .

B

Enter the fax number using the number keys.

To specify a destination using a Quick Dial key, see “Using the Quick Dial Keys”.
If you make a mistake, press the 

{

Clear/Stop

}

 key, and then enter again.

C

Press the 

{

Start

}

 key.

The machine starts to scan the original and stores it in memory. When scan-
ning ends, the Communicating indicator lights and transmission starts.

Note

You can insert pauses and tones in a fax number.

For the maximum number of digits for a destination, see “Maximum Values”.

Reference

p.47 “Entering a pause”
p.47 “Entering a tone”
p.57 “Using the Quick Dial Keys”
p.186 “Maximum Values”

Summary of Contents for Aficio MP 2500













































































































































































































Reviews: