• It is recommended to use long-grained paper for the best print quality. If short-grained paper is being
used, it might be the cause of paper jams.
• Use neutral paper. Do not use acid paper to avoid any damage to the drum unit.
• Avoid using coated paper such as vinyl coated paper.
• Avoid using preprinted or highly textured paper.
• It is recommended to use labels or transparencies which are designed for use in laser printers.
• Avoid feeding labels with the carrier sheet exposed, or the printer will be damaged.
• Before loading paper with holes such as organizer sheets, be sure to fan the stack well.
• Do not use organizer sheets that are stuck together. The glue that is used might caused damaged to
the printer.
• When printing on the back of pre-printed paper, if the paper is curled, be sure to straighten the paper
as much as possible.
• Different types of paper should not be loaded at the same time in the paper tray to avoid any paper
jams or misfeeds.
Paper tray capacity
Paper Tray
Manual feed slot
Paper Capacity
250 sheets (80 g/m
2
or 21lb)
Single sheet
Print delivery
Face down output tray capacity:
Maximum 100 sheets (80 g/m
2
) face down only
• Face-down: Delivery with the printed face of the paper downwards.
Printable Area
The edges of the paper that cannot be printed on are shown below.
1. Appendix: Specifications
6
1
Summary of Contents for HL-F1
