Error Code
(Hex)
Symptom
Probable Cause
Solution
88
Recording paper jam.
(The regist rear sensor
actuator is being push down
even after feeding paper.)
Paper is jammed.
Remove the jammed paper.
Regist rear sensor
actuator caught on the
surrounding parts.
Reassemble the regist rear
sensor actuator.
Foreign materials in the
paper path.
Remove foreign materials.
Regist rear sensor
defective
Replace the high-voltage
PS PCB ASSY.
Paper feed roller
defective
Replace the Paper feed
roller.
F/R solenoid defective
Replace the F/R solenoid.
Main motor defective
Replace the main motor
ASSY.
Main PCB defective
Replace the main PCB.
89
Recording paper jam in the
manual slot (The regist rear
sensor actuator is not pushed
down after a certain time
elapses after paper feeding.)
Paper is jammed.
Remove the jammed paper.
Regist rear sensor
actuator caught on the
surrounding parts.
Reassemble the regist rear
sensor actuator.
Foreign materials in the
paper path.
Remove foreign materials.
Regist rear sensor
defective
Replace the high-voltage
PS PCB ASSY.
Main motor defective
Replace the main motor.
Main PCB defective
Replace the main PCB.
8A-A0
Not used.
-
-
2. Appendix: Troubleshooting Guide
30
2
Summary of Contents for HL-F1
