4. Check the paper used meets the recommended paper specifications. (
"Paper Specifications" in
"Appendices")
F-5 Curl or Wave
User Check
1. Check the paper used meets the recommended paper specifications. Both high temperature and
humidity will cause paper to curl.
2. If the printer is used infrequently, the paper may have sat for too long in the paper tray. Turn over the
stack of paper in the paper tray. Also, try rotating the paper 180° in the paper tray.
3. Check that the paper used meets the Media Type setting in the driver.
• For no paper supplied as the cause of a malfunction, see M-4 "No paper supplied' in "Malfunctions"
in this Chapter.
F-6 Paper pickup
Possible cause and Remedy
1. Disconnection of the pickup solenoid harness
• Is the harness of the pickup solenoid disconnected?
Yes: Reconnect the harness.
2. Pickup solenoid harness failure
• Does the harness of the pickup solenoid work correctly?
No: Replace the harness of the pickup solenoid.
3. Pressure plate gear damage
• Is the pressure plate gear damaged?
Yes: Replace the pressure plate gear.
4. Clutch gear damage
• Is the clutch gear damaged?
Yes: Replace the gear unit.
Software Setting Problems
The printer may not print the data correctly if there are incorrect software settings.
Troubleshooting Guide
207
6
Summary of Contents for HL-F1
