background image

19

WARRANTY

Proof  of  purchase  must  be  presented  when  requesting 
warranty service. 
Limited to RIDGID

®

 hand held and stationary power tools 

purchased 2/1/04 and after. This product is manufactured 
by One World Technologies, Inc. The trademark is licensed 
from RIDGID, Inc. All warranty communications should be 
directed to One World Technologies, Inc., attn: RIDGID Hand 
Held  and  Stationary  Power  Tool  Technical  Service  at  (toll 
free) 1-866-539-1710. 

90-DAY SATISFACTION GUARANTEE POLICY 

During the first 90 days after the date of purchase, if you are 
dissatisfied with the performance of this RIDGID

®

 Hand Held 

and Stationary Power Tool for any reason you may return 
the tool to the dealer from which it was purchased for a full 
refund or exchange. To receive a replacement tool you must 
present proof of purchase and return all original equipment 
packaged with the original product. The replacement tool 
will be covered by the limited warranty for the balance of 
the 3 YEAR service warranty period. 

WHAT IS COVERED UNDER THE 3 YEAR 
LIMITED SERVICE WARRANTY 

This warranty on RIDGID

®

 Hand Held and Stationary Power 

Tools covers all defects in workmanship or materials and 
normal wear items such as brushes, chucks, motors, switch-
es, cords, gears and even cordless batteries in this RIDGID

® 

tool for three years following the purchase date of the tool. 
Warranties for other RIDGID

®

 products may vary. 

HOW TO OBTAIN SERVICE

To obtain service for this RIDGID

®

 tool you must return it; 

freight prepaid, or take it in to an authorized service center 
for RIDGID

®

 branded hand held and stationary power tools. 

You may obtain the location of the authorized service cen-
ter nearest you by calling (toll free) 1-866-539-1710 or by 
logging  on  to  the  RIDGID

®

  website  at  www.ridgid.com. 

When  requesting  warranty  service,  you  must  present  the 
original dated sales receipt. The authorized service center will 
repair any faulty workmanship, and either repair or replace 
any part covered under the warranty, at our option, at no 
charge to you.

One World Technologies, Inc.

P.O. Box 35, Hwy. 8

Pickens, SC 29671

RIDGID

®

 HAND HELD AND STATIONARY POWER TOOL

3 YEAR LIMITED SERVICE WARRANTY 

WHAT IS NOT COVERED

This  warranty  applies  only  to  the  original  purchaser  at 
retail and may not be transferred. This warranty only covers 
defects arising under normal usage and does not cover any 
malfunction, failure or defect resulting from misuse, abuse, 
neglect,  alteration,  modification  or  repair  by  other  than 
an  authorized  service  center  for  RIDGID

®

  branded  hand 

held and stationary power tools. Consumable accessories 
provided with the tool such as, but not limited to, blades, 
bits and sand paper are not covered.  

RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC. 
MAKE  NO  WARRANTIES,  REPRESENTATIONS  OR 
PROMISES AS TO THE QUALITY OR PERFORMANCE 
OF ITS POWER TOOLS OTHER THAN THOSE SPECIFI-
CALLY STATED IN THIS WARRANTY. 

ADDITIONAL LIMITATIONS

To  the  extent  permitted  by  applicable  law,  all  implied 
warranties, including warranties of MERCHANTABILITY or 
FITNESS FOR A PARTICULAR PURPOSE, are disclaimed. 
Any implied warranties, including warranties of merchant-
ability  or  fitness  for  a  particular  purpose,  that  cannot  be 
disclaimed under state law are limited to three years from the 
date of purchase. One World Technologies, Inc. and RIDGID, 
Inc.  are  not  responsible  for  direct,  indirect,  incidental  or 
consequential  damages.  Some  states  do  not  allow 
limitations  on  how  long  an  implied  warranty  lasts  and/or 
do  not  allow  the  exclusion  or  limitation  of  incidental  or 
consequential damages, so the above limitations may not 
apply to you. This warranty gives you specific legal rights, 
and you may also have other rights which vary from state 
to state.

Summary of Contents for AC9944





















Reviews: