background image

10

UNPACKING

This product has been shipped completely assembled.

n

  Carefully remove the tool and any accessories from the 

box.

n

  Make  sure  that  all  items  listed  in  the  packing  list  are 

included.

n

  Inspect the tool carefully to make sure no breakage or 

damage occurred during shipping.

n

  Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the tool.

n

  If  any  parts  are  damaged  or  missing,  please  call 

1-866-539-1710 for assistance.

PACKING LIST

Coil Roofing Nailer
Carrying Case
Oil
Hex Key
Eye Protection
Fastener Guide
Operator’s Manual

ASSEMBLY

WARNING:

If any parts are missing do not operate this tool 
until  the  missing  parts  are  replaced.  Failure  to 
do  so  could  result  in  possible  serious  personal 
injury.

WARNING:

Do  not  attempt  to  modify  this  tool  or  create 
accessories  not  recommended  for  use  with  this 
tool. Any such alteration or modification is misuse 
and could result in a hazardous condition leading 
to possible serious personal injury.

OPERATION

APPLICATIONS

You may use this tool for the purposes listed below:

n

  Asphalt & Fiberglass Shingles

n

  Waterproof Tar Paper

n

  Roofing Felt

n

  Fire Wall (Exterior Gypsum Board)

n

  House Wrap

n

  Cement Board

n

  Insulation Board

n

  Metal Drip Edges

n

  Siding

n

  Vapor Barrier

n

  Upholstery Trim Panels

DANGER:

Do not use oxygen, combustible gases or bottled 
gases as a power source for this tool. The tool will 
explode and cause death or serious injury.

WARNING:

Do  not  allow  familiarity  with  tools  to  make  you 
careless. Remember that a careless fraction of a 
second is sufficient to inflict severe injury.

WARNING:

Always wear safety goggles or safety glasses with 
side shields when operating tools. Failure to do so 
could result in objects being thrown into your eyes 
resulting in possible serious injury.

WARNING:

Disconnect  the  tool  from  the  air  supply  before 
leaving the work area, moving the tool to another 
location,  or  handing  the  tool  to  another  person. 
Failure to do so could result in serious personal 
injury.

Summary of Contents for R175RNA























Reviews: