RIDGID R175RNA Operator'S Manual Download | Manualshive

Page: 19 / 22

background image

19

TROUBLESHOOTING

Air leak near the top of the tool or
in the trigger area

PROBLEM

POSSIBLE CAUSE

SOLUTION

Loose screws
Worn or damaged O-rings or
seals

Tool does nothing or operates
sluggishly

Tool jams frequently

Tighten screws
Install Overhaul Kit

Inadequate air supply
Inadequate lubrication
Worn or damaged O-rings or bumper

Tighten screws
Install Overhaul Kit

Verify adequate air supply
Lubricate the tool
Install Overhaul Kit

Air leak near the bottom of the
tool

Loose screws
Worn or damaged O-rings or bumper

Incorrect fasteners
Damaged fasteners
Loose magazine or nose screws
Dirty magazine
Worn or damaged driver

Verify that fasteners are the correct size
Replace fasteners
Tighten screws
Clean magazine
Install Driver Maintenance Kit

ACCESSORIES

To order parts and maintenance kits, call 1-866-539-1710.
Driver Maintenance Kit ....................................................................................................................................079006001111
Overhaul Kit.....................................................................................................................................................079006001110
Oil and Wrench Kit ..........................................................................................................................................079006001115

WARNING:

Current attachments and accessories available for use with this tool are listed above. Do not use any attachments
or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not
recommended can result in serious personal injury.

«
...
17
18
19
20
21
...
»

Summary of Contents for R175RNA























Reviews:

No comments

Related manuals for R175RNA

Brand: NEO TOOLS Pages: 32

Fulscope 76J Series Model C

Brand: ABB Pages: 58

Brand: DeWalt Pages: 156

ShopMaster CL180BN

Brand: Delta Pages: 17

Brand: Makita Pages: 48

Brand: Makita Pages: 96

TRE550 Heavy Duty

Brand: Stanley Pages: 2

Pro Sharp Shooter TR200

Brand: Stanley Pages: 2

Brand: Stanley Pages: 13

Brand: Stanley Pages: 24

SB1850BN FATMax

Brand: Stanley Pages: 36

Brand: Stanley Pages: 39

Brand: Stanley Pages: 48

Bostitch BT1855

Brand: Stanley Pages: 56

Brand: Stanley Pages: 70

Brand: Stanley Pages: 130

Brand: STEINEL Pages: 37

2by4 Contractor Series

Brand: DeVillbiss Air Power Company Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands