102
B
EDIENUNG
Version dreiphasig
1.
(VERSION DREIPHASIG 8-10kVA):
3 Kabel mit Querschnitt
6 mm
2
(ERDE, L2 und L3) und 2 Kabel mit Querschnitt 10
mm
2
(N, L1) am Eingang verwenden (Anmerkung: L1 und
L2 haben einen größeren Querschnitt, weil sie im Bypass-
Betrieb den gesamten Eingangsstrom leiten). Für den
Ausgang 3 Kabel mit Querschnitt 10 mm
2
(ERDE, N und L)
verwenden.
Siehe auch die nebenstehende Abbildung:
- Die von dem 63A magnetothermischen Schutzschalter
kommenden Kabel in die Schutzhüllensperre P2 (Eingangslinie)
einsetzen.
- Die
von
den
Lasten
kommenden
Kabel
in
die
Schutzhüllensperre P1 (Ausgangslinie) einsetzen.
- Die Kabel auf der angegebenen Länge abisolieren.
- Das abisolierte Teil in die Spitzen aus dem Lieferumfang
einsetzen.
(VERSION DREIPHASIG 6,5kVA):
3 Kabel mit Querschnitt
4 mm
2
(ERDE, L2 und L3) und 2 Kabel mit Querschnitt 6
mm
2
(N, L1) am Eingang verwenden (Anmerkung: L1 und
L2 haben einen größeren Querschnitt, weil sie im Bypass-
Betrieb den gesamten Eingangsstrom leiten). Für den
Ausgang 3 Kabel mit Querschnitt 6 mm
2
(ERDE, N und L)
verwenden.
Siehe auch die nebenstehende Abbildung:
- Die von dem 63A magnetothermischen Schutzschalter
kommenden Kabel in die Schutzhüllensperre P2 (Eingangslinie)
einsetzen.
- Die
von
den
Lasten
kommenden
Kabel
in
die
Schutzhüllensperre P1 (Ausgangslinie) einsetzen.
- Die Kabel auf der angegebenen Länge abisolieren.
- Das abisolierte Teil in die Spitzen aus dem Lieferumfang einsetzen.
2.
Die Kabel an den entsprechenden Klemmen anschließen. Dabei müssen die folgenden Abweisungen
genau eingehalten werden:
Eingangsleitung
a - Sicherstellen,
dass
der
vorgeschaltete
magnetothermische Schutzschalter geöffnet ist.
b - Das Erdkabel an Klemme 5 anschließen.
c - Das Nullleiterkab,el an Klemme 1 anschließen.
d - Die Phasenkabel an die Klemmen 2, 3 und 4
anschließen (für L1 das rote Kabel verwenden).
Ausgangsleitung
a - Das Erdkabel an Klemme 6 anschließen.
b - Das Nullleiterkabel an Klemme 7 anschließen.
c - Das Phasenkabel an Klemme 8 anschließen.
Bypass-Leitung
a - Sicherstellen, dass die Klemmen 9 und 10
überbrückt sind. Das wird für einen richtigen Betrieb
der USV benötigt.
3.
Die Kabelführung an der Flansch festziehen, das Gehäuse schließen und mit der vorher abgenommenen
Schraube befestigen.
Summary of Contents for SENTINEL DUAL SDL 10000
