background image

20013748

GB

INFORMATION ABOUT THE INSTRUCTION MANUAL

INTRODUCTION

The instruction manual supplied with the burner:
-

is an integral and essential part of the product and must not be sepa-
rated from it; it must therefore be kept carefully for any necessary
consultation and must accompany the burner even if it is transferred
to another owner or user, or to another system. If the manual is lost
or damaged, another copy must be requested from the Technical

Assistance Service 

 of the area;

-

is designed for use by qualified personnel;

-

offers important indications and instructions relating to the installation
safety, start-up, use and maintenance of the burner.

DELIVERY OF THE SYSTEM AND THE INSTRUCTION MAN-
UAL

When the system is delivered, it is important that:
-

The instruction manual is supplied to the user by the system manu-
facturer, with the recommendation to keep it in the room where the
heat generator is to be installed.

-

The instruction manual shows:
-

the serial number of the burner;

-

the address and telephone number of the nearest Assistance 
Centre;

-

The system supplier carefully informs the user about:
-

the use of the system, 

-

any further tests that may be necessary before the system is 
started up, 

-

maintenance and the need to have the system checked at least 
once a year by the manufacturer or another specialised techni-
cian.

To ensure a periodic check, 

 recommends the drawing up 

of a Maintenance Contract.

..................................................................................

..................................................................................

..................................................................................

..................................................................................

Summary of Contents for 20013628





















Reviews: