background image

20197230

GB

Information and general warnings

2.1.4

Delivery of the system and the instruction 
manual

When the system is delivered, it is important that:

the instruction manual is delivered to the user by the system
manufacturer, with the recommendation to keep it in the
room where the heat generator is to be installed.

The instruction manual shows:
- the serial number of the burner;

- the address and telephone number of the nearest Assis-

tance Centre

The system supplier must carefully inform the user about:
- the use of the system; 
- any further tests that may be required before activating the

system; 

- maintenance, and the need to have the system checked at

least once a year by a representative of the manufacturer
or another specialised technician.
To ensure a periodic check, the manufacturer recom-
mends the drawing up of a Maintenance Contract.

2.2

Guarantee and responsibility

The Manufacturer guarantees its new products from the date of
installation, in accordance with the regulations in force and/or the
sales contract. At the moment of the first start-up, check that the
burner is integral and complete.

In particular, the rights to the guarantee and the responsibility will
no longer be valid, in the event of damage to things or injury to
people, if such damage/injury was due to any of the following
causes:

incorrect installation, start-up, use and maintenance of the
burner;

improper, incorrect or unreasonable use of the burner;

intervention of unqualified personnel;

carrying out of unauthorised modifications on the equipment;

use of the burner with safety devices that are faulty, incor-
rectly applied and/or not working;

installation of untested supplementary components on the
burner;

powering of the burner with unsuitable fuels;

faults in the fuel supply system;

continuation of use of the burner when a fault has occurred;

repairs and/or overhauls incorrectly carried out;

modification of the combustion chamber with inserts that
prevent the regular development of the structurally estab-
lished flame;

insufficient and inappropriate surveillance and care of those
burner components most likely to be subject to wear and
tear;

use of non-original components, including spare parts, kits,
accessories and optional;

force majeure.

The manufacturer furthermore declines any and every re-
sponsibility for the failure to observe the contents of this
manual.

.........................................................................................

.........................................................................................

.........................................................................................

.........................................................................................

WARNING

Failure to observe the information given in this
manual, operating negligence, incorrect installa-
tion and carrying out of non authorised modifica-
tions will result in the annulment by the
manufacturer of the guarantee that it supplies with
the burner. 

Summary of Contents for 3749251





























Reviews: