95
I
NSTALLATION ET
U
TILISATION
M
ISE EN MARCHE SUR BATTERIE
1) En présence du réseau, presser le bouton “Marche” pendant une seconde environ (jusqu’à entendre un bip
sonore) et relâcher immédiatement. Toutes les icônes de l’afficheur s’allument pendant 1 seconde et l’ASI
émet un bip. Une vérification de la tension de batterie est effectuée et, si tout est normal, seules les
indications de fonctionnement sur batterie, la barre de charge, la barre batterie accompagnée d’un bip
intermittent restent allumées
2) Mettre en marche les appareils branchés à l’ASI.
A
RRET DE L
’ASI
Pour arrêter l’ASI, presser le bouton “arrêt” jusqu’à entendre un bip puis relâcher le bouton. Toutes les
DELs du panneau afficheur s’allument pendant quelques instants, après quoi toutes les signalisations
s’éteignent à part la DEL d’“anomalie/stand-by” qui commence à clignoter et l’ASI revient en condition de
stand-by.
Pour arrêter l’UPS alors que le réseau amont est absent et que la fonction d’arrêt programmé est activée,
appuyer sur la touche OFF (environ 5 s ) jusqu’à entendre un 2ème beep sonore. Pendant la phase arrêt, tous
les voyants LED sont éclairés et l’UPS émet un signal sonore continu.
F
ONCTIONS SUPPLEMENTAIRES
(
EXECUTEES A PARTIR DU PANNEAU FRONTAL
)
ASI en fonctionnement sur stand by
Pour
effacer un arrêt programmé par logiciel
(1)
, presser la touche “ON” jusqu’à entendre le
2
ème
bip
puis relâcher immédiatement (5 secondes environ), ou bien presser la touche “OFF” jusqu’à entendre un
bip
puis relâcher immédiatement (2 secondes environ).
ASI en fonctionnement sur réseau
Pour
exclure
l’alarme
intermittente de l’ASI pendant une phase finale d’un arrêt programmé par
logiciel, presser la touche “ON” jusqu’à entendre le
1er bip
et relâcher immédiatement (2 sec. environ)
Pour
effacer un arrêt programmé par logiciel
(1)
, presser la touche “ON” jusqu’à entendre le
2
ème
bip
puis relâcher immédiatement (5 secondes environ), ou bien presser la touche “OFF” jusqu’à entendre un
bip
puis relâcher immédiatement (2 secondes environ).
Pour exécuter un
test de batterie,
presser la touche “ON” jusqu’à entendre le
3ème bip
et relâcher
immédiatement (7 sec. environ). A ce point le test commence par un clignotement cyclique des DELs de
l’afficheur. Une fois terminé, si les batteries sont bonnes, l’ASI revient en mode sur réseau avec les
signalisations habituelles, autrement, en cas de panne de la batterie ou de décharge, la DEL de “panne
batterie”s’allume, accompagnée ou pas d’un signal sonore (consulter les tableaux du chapitre
ALARMES et SIGNALISATIONS pour de plus amples détails).
Pour visualiser de façon indicative la
valeur de la tension de réseau
en entrée de l’ASI sur la barre
lumineuse de batterie, presser la touche “ON”pendant plus de 10 sec jusqu’à entendre le
4ème bip
. Dès
que l’on relâche la touche, l’indication normale de la tension de batterie sera de nouveau visualisée sur la
barre de batterie.
ASI en fonctionnement sur batterie
Pour
exclure l’alarme
intermittente de l’ASI pendant une phase de fonctionnement sur batterie, presser
la touche “ON” jusqu’à entendre le
1
er
bip
puis relâcher immédiatement (2 sec. environ)
N.B. il n’est pas possible d’exclure l’alarme de l’ASI quand ce dernier se trouve en état de fin de
décharge (1 bip par seconde)
Pour
effacer un arrêt programmé
par logiciel
(1)
, presser la touche “ON” jusqu’à entendre le
2
ème
bip
et relâcher immédiatement (5 sec. environ)
(1)
Pour de plus amples détails sur les fonctions activables par logiciel, consulter le manuel du logiciel présent dans le CD-
Rom fourni avec l’appareil.
Summary of Contents for Dialog Plus
