background image

2

TECHNICAL DATA

(1)

Reference conditions: Room temperature 20°C - Gas temperature 15°C - Barometric pressure 1013 mbar - Altitude 0m above sea level.

(2)

Socket pressure 7)(A)p.4 with zero pressure in the combustion chamber.

(3)

Sound pressure measured in manufacturer's combustion laboratory, with burner operating on test boiler and at maximum rated output. The
sound power is measured with the “Free Field” method, as per EN 15036, and according to an “Accuracy: Category 3” measuring accuracy,
as set out in EN ISO 3746.

STRUCTURAL VERSIONS 

GAS CATEGORIES

MODEL

RS 25/M BLU

RS 35/M BLU

RS 35/M BLU

TYPE

876 T

877 T

877 T

OUTPUT 

(1)

MAX.

kW

125 - 370
108 - 320

202 - 480
174 - 413

202 - 480
174 - 413

Mcal/h

MIN.

kW

Mcal/h

45
39

72
62

72
62

FUEL

NATURAL GAS: G20 - G21 - G22 - G23 - G25

G20

G25

G20

G25

G20

G25

- net calorific value

kWh/Sm

3

Mcal/Sm

3

9.45

8.2

8.13

7.0

9.45

8.2

8.13

7.0

9.45

8.2

8.13

7.0

- absolute density

kg/Sm

3

0.71

0.78

0.71

0.78

0.71

0.78

- max. delivery

Sm

3

/h

39

45

51

59

51

59

- pressure at max. delivery (2)

mbar

15.6

21.8

14.1

24.7

14.1

24.7

OPERATION

• On-Off (1 stop min each 24 hours).
• Progressive two-stage or modulating by kit (see ACCESSOIRES).

STANDARD APPLICATIONS

Boilers: water, steam, diathermic oil

AMBIENT TEMPERATURE

°C

0 - 40

COMBUSTION AIR TEMPERATURE

°C max

60

ELECTRICAL SUPPLY

V

Hz

230 ~ +/-10%
50/60 - single-phase

230 - 400 with neutral ~ +/-10%
50/60 - three-phase

ELECTRIC MOTOR

rpm

W

V

2800

300

220 - 240

2800

420

220 - 240

2780

450

220/240-380/415

ACCELERATION CURRENT

A

15

17

14 - 10

WORKING CURRENT

A

3.2

3.5

2 - 1.4

MOTOR CAPACITOR

 

F/V

12.5/260

12.5/420

-

IGNITION TRANSFORMER

V1 - V2

I1 - I2

230 V - 1 x 15kV

1 A - 25mA

ELECTRICAL POWER CONSUMPTION

W max

600

700

750

PROTECTION LEVEL

IP40

NOISE LEVELS 

(3)

SOUND PRESSURE
SOUND POWER

dBA

68
79

70
81

70
81

MODEL

POWER SUPPLY

BLAST TUBE LENGTH

  mm

RS 25/M BLU

Single-phase
Single-phase

230
365

RS 35/M BLU

Single-phase
Single-phase

Three-phase
Three-phase

230
365
230
365

DESTINATION COUNTRY

GAS CATEGORY

SE - FI - AT - GR - DK - ES - GB - IT - IE

PT - IS - CH - NO

I

2H

DE

I

2ELL

NL

I

2L

 - I

2E

 - I

2

 (43,46 ÷ 45,3 MJ/m

3

 (0°C))

FR

I

2Er

BE

I

2E(R)B

LU - PL

I

2E

 

Summary of Contents for RS 25/M BLU





















Reviews: