RIKA E15895, Manual

|27

EN

26

Dimensions PARO MULTIAIR

FB-S

B

H

FB-T

T

RO-H

RO-T2

RO-T3

F-S

F-H

R-H

RO-S=R-S

K1-S=K2-S

K2-H

K1-H

RO-T1

F-

R-

K-

Dimensions

Height

[mm]

1132

Width

[mm]

952

Corpus depth

[mm]

505

Weight

Weight without shell

[kg]

~ 265

Weight with steelpanel

[kg]

~ 270

Weight with stonepanel

[kg]

~ 315

Flue pipe connection

R - Ø Flue pipe outlet

[mm]

130

RO - H original angle pipe connection 
height

[cm]

162

RO - T1 original angle pipe total depth

[cm]

79

RO - T2 original angle pipe distance to 
rear wall

[cm]

28

RO - T3 Deapth from rear wall to middle 
of flue pipe

[cm]

10

RO - S original angle pipe side distance

[cm]

41

R - H Rear connection height

[cm]

96

R - S Rear connection side distance

[cm]

41

Fresh air connection

F - Ø Diameter

[mm]

125

F - H Connection height

[cm]

13

F - S Side distance

[cm]

38

FB - S Floor connection side distance

[cm]

38

FB - T Floor connection depth

[cm]

23

Convection air connection

K - Ø Diameter

[mm]

100

K1 - H/ K2 - H Connection height

[cm]

103/75

K1 - S/ K2 - S Side distance

[cm]

12/12

Amount of fuel

Nominal Load

Part Load

Log operation

2,2 kg

1,1 kg

Pellet operation

~1,9 kg*

~0,6 kg*

Burning time at full 
pellet hopper

~ 14 h

~ 43 h

*Practical values   may vary depending on pellet quality.

Note

Pellet consumption depends on the size of the pellets. The larger 
the pellet, the slower the feed and vice versa.

Technical data PARO MULTIAIR

Technical Data

Pellets

Logs

Heating capacity range

[kW]

2,5 - 8

4 - 8

Room heating capacity 
depending on house coating

[m3]

50 - 220

90 - 220

Consumption

[kg/h]

bis 1,9

bis 2,2

Pellet container lid capacity*

[l]/[kg]

47/~30

-

Electric supply

[V]/[Hz]

230/50

230/50

Average electrical input

[W]

~ 20

~ 20

Fuse

[A]

2,5

2,5

Efficiency

[%]

91,3

91

CO

2

[%]

11,9

11,3

CO-emission on 13 % O

2

[mg/m

N

3

]

79,5

580

Dust emission

[mg/m

N

3

]

19,5

25,5

Exhaust

[g/s]

5,3

5,8

Exhaust temperature

[°C]

170,3

152,5

Chimney draft requirement

[Pa]

3

12

*The capacity in kg may deviate due to different pellet bulk 
densities.

The owner of small firing systems or the person authorised for the 
small firing system is to keep the technical documentation and is to 
submit it to the authorities or the chimney sweep on request.

Note

Please observe the national and European standards as well as 
local regulations concerning the installation and operation of 
firing installations!

Packaging

Your first impression is important to us!

The packaging of your new stove provides excellent protection 
against damage. However damage to the stove and accessories 
may still occur during transport.

Note

Therefore please check your stove on receipt for damage and 
completeness! Report any deficiencies to your dealer immediately! 
Pay particular attention during unpacking that the stone panels 
remain intact. Scratches to the material can easily occur. Stone 
panels are excluded from the warrant.

The packaging of your new stove is environmentally neutral to a 
great extent.

Tip

The wood used in the packaging has not been surface treated 
and may therefore be burnt in your woodburning stove (not in a 
pelletstove!). The cardboard and film (PE) can be depolluted  via 
the municipal waste collection for recycling.

Electrical connection

The stove is supplied with an approx. 2 m long connecting cable with 
a Euro-plug. This cable is to be connected to a 230 V/50 Hz socket. 
The average electrical power consumption is about 20 watts in 
heating operation and approx. 150 watts during automatic ignition. 
The connection cable must be laid in a way that there is no contact 
to any sharp edges or hot surfaces of the stove.