background image

4 How to Use

                                                                                                     

4-3. Precautions for system designing 

 

- 17 -

 

Introducing protective measures against lightning 

If cables are installed outside the factory/plant, or if internal cables are installed in the same duct as the 
cables coming from outside the factory/plant, "lightning" will cause problems. Because lightning acts as a 
large emission source while cables act as a receiving antenna, devices connected to the cables may be 
damaged. 
Lightning cannot be prevented. Cables installed in a metal conduit or under the ground cannot be 
completely protected from inductive lightning surge caused by lightning. Although complete elimination of 
disasters caused by lightning is impossible, the following protective measures can be taken. 
 

Protection against 

lightning 

Take appropriate measures in accordance with the importance of the facilities 
and the environment. 

  Provide protection by a lightning arrester (cable arrester). 

(Although inductive lightning surge can be transmitted through the cable, it is 
prevented by installing a lightning arrester before the field devices and central 
processing equipment. For information on how to use a lightning arrester, 
please contact the manufacturer.) 

Grounding 

In addition to lightning, there are more sources of surge noise. To protect units 
from these noise sources, the units must be grounded. 

*  The lightning arrester has a circuit to remove a surge voltage which damages field devices, so that signals 

may be attenuated. Before installing a lightning arrester, verify that it works properly. 

 
 

 

Summary of Contents for SD-1DOX-AS






































































Reviews: